Table of Contents
Advertisement
Quick Links
600R Series Remote Access Points
Installation Guide
The 600R Series access points are dual-radio tri-band 802.11ax Wi-Fi 6E remote access points that provide
connectivity for both wired and wireless client devices.
Package Contents
The following materials are included with this product:
AP-605R access point x 1
n
AC-to-DC power adapter (with power cord) x 1
n
(For AP-605R bundle only) AP-605CM12 LTE CAT12 cellular module (pre-installed) x 1
n
To simplify the ordering, Aruba offers the AP-605R bundle that combines an AP-605R access point, a power adapter
(with power cord) and a AP-605CM12 LTE CAT12 cellular module (pre-installed)
Hardware Overview
Figure 1 AP-605R Front View
1
2
3
600R Series Remote Access Points | Installation Guide
System Status LED
LCD Panel
LCD Button
1
Advertisement
Table of Contents
Related Manuals for HP 600R Series
Summary of Contents for HP 600R Series
- Page 1 600R Series Remote Access Points Installation Guide The 600R Series access points are dual-radio tri-band 802.11ax Wi-Fi 6E remote access points that provide connectivity for both wired and wireless client devices. Package Contents The following materials are included with this product: AP-605R access point x 1 AC-to-DC power adapter (with power cord) x 1...
- Page 2 Figure 2 AP-605R Bundle Front View System Status LED LCD Panel LCD Button The antennas of the LTE module are in a folded position when taken out of the package. To ensure the antennas function well, put the antennas in a vertical position as shown in . System Status LED The system status LED is located on the top panel of the access point indicates the system status of the access point.
- Page 3 LED Display Settings The LEDs have three operating modes that can be selected in the system management software: Normal mode: default after power on. Refer to Table Off mode: the LED is off Blink mode: the LED blinks green Pressing the reset button for less than 10 seconds during normal operation will toggle the LED mode between “normal”...
- Page 4 Figure 3 600R Series Rear and Side View Reset Button Micro-B Console Port E0 Ethernet Port (Orange) E1 Ethernet Port (Orange and Blue) E2 Ethernet Port (Blue) E3 Ethernet Port (Blue) E4 Ethernet Port (Red) USB Interface Kensington Lock Slot...
- Page 5 (enabled/disabled) and access credentials are updated to match what’s configured there. State and credentials are maintained if the AP is power-cycled or rebooted. Ethernet Ports The 600R Series access point has five Ethernet ports (E0 - E4), shown in Figure The E0 port is a 100/1000Base-T auto-sensing MDI/MDIX uplink port .
- Page 6 Table 3: Ethernet Port LEDs Color/State Meaning Left Meet one of the following conditions: access point is powered off port is disabled no link established Green - blinking Activity detected on the port Green - solid Link established at optimum speed (1Gbps or 2.5Gbps) Amber - solid Link established at reduced speed (100Mbps) Right (E4 only)
-
Page 7: Access Point Installation
(class 3.2 per ETSI 300 019). You can put the 600R Series access point on any flat surface such as a desktop. Installing the SIM Card (For AP-605R Bundle Only) To use the AP-605CM12 cellular module, you need to install a SIM card to the SIM card tray on the AP-... - Page 8 time, only one SIM card is active and functional, the SIM slot 1 and SIM slot 2 can not be used simultaneously. If you have only one SIM card, it is recommended to insert your SIM card to the SIM slot 1. To install a SIM card into the SIM tray, perform the following steps: 1.
- Page 9 3. Insert the SIM ejector needle into the small hole on the SIM card tray. The SIM card tray will pop open. Figure Figure 9 Opening the SIM Card Tray 4. Pull out the SIM card tray and insert a SIM card into the SIM tray. 5.
-
Page 10: Verifying Post-Installation Connectivity
Figure 11 Installing Cellular Module onto Access Point Software For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick Start Guide. Aruba access points are classified as radio transmission devices, and are subject to government regulations of the host country. -
Page 11: Regulatory Information
The regulatory model number RMN is not the marketing name or model number of the product. The following regulatory model numbers apply to the 600R Series AP-605R RMN: APINR605 AP-605CM12 RMN: APINCM12 Changes or modifications not expressly approved by the party responsible for compliance could void the user’s author-... - Page 12 Para mais informações, consulte o site da Anatel: https://www.gov.br/anatel/pt-br O uso deste equipamento é restrito a ambientes fechados e proibido em plataformas petrolíferas, carros, trens, embarcações e no interior de aeronaves abaixo de 3.048 m (10.000 pés). Canada This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations.
- Page 13 Wireless Channel Restrictions 5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK (NI)).
- Page 14 Korean México La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. Нормативные...
- Page 15 前 項 合法 通 信 ， 指依 電 信 法 規定 作 業 之 無線 電 通 信 。 低 功率 射 頻 電 機須 忍 受 合 法通 信 或 工 業 、 科 學 及 醫 療 用電 波 輻 射 性電 機 設 備 之干 擾 。 1.
-
Page 16: Contacting Support
Medical 1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 60950-1 or IEC 60601-1 certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1. 3.