Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for P2 MOBILE TECHNOLOGIES LIMITED Z100
Summary of Contents for P2 MOBILE TECHNOLOGIES LIMITED Z100
- Page 1 Z100 Wireless Access Point...
-
Page 2: Package List
1. Introduction Z100 is a dual-band 2x2streams and chains indoor Wi-Fi AP, which is complied with the IEEE802.11n standard and designed for high-density deployments in offices, schools, hospitals and hotels that require premium performance. -
Page 3: Installation
Console port Also names as RJ-11, used to manage Z100 software. Reset button Pressing the button longer than 5s to restore the device to factory defaults and reset the device. DC power connector used for connecting the power adapter USB port supports a USB 2.0 connector(... - Page 4 Installation tool: • Screws and screw-driver Installation site: Please ensure the visibility ofproduct and no tall buildings and woods block between them. Installation procedure Wall mounting Drive two screws fist in the wall. The distantbetween two screws mounted on the wall is 40mm.
- Page 5 Ceiling mounting: Fasten ceiling rails by pushing bracket as the indicated direction Secure the screw to fasten bracket assembly. Align securing hookof AP with bracket (see dotted line), and then push AP close to bracket until AP has been fully Locked Go through locking holes by cabletie to safely content AP with bracket...
-
Page 6: Led Definition
5. LED Definition Function State-Color Indication AP power / ready status Steady - Green APis ready Flashing - Green AP is managed by controller AP hardware failure No power to AP Network Link Status Steady - Green 1000Mbps Ethernet link negotiated Steady- Yellow Reserved for link speed (NIB in PCB) Flashing... -
Page 7: Product Specification
Input the default IP address 192.168.188.251 in the address bar of the web browser and press Enter. Enter username and password (username: admin, password: password), after password authentication is successful, the web page is displayed. 7. Product Specification Physical specification Dimensions 160 mm x 160 mm x 40mm(Width x Length x Height) Weight... - Page 8 Chromium, and Bromine. CIG products comply with this requirement and all marked with “RoHS” shown at the left. China RoHS Z100 AP complies with China environmental declaration requirements and is labeled with “EFUP 20” label shown as follows. 有毒有害物质声明 Hazardous Materials Declaration 部件名称...
-
Page 9: Safety And Regulatory Compliance
The Environment-Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual. 9. Safety and Regulatory compliance Z100 AP has been tested and complied with the standards as follows: • FCC Part 15 Subpart C 15.247 (US) •... -
Page 10: Technical Support
Solution Check that the power adapter is plugged into a live AC outlet. Check the power cable for shorts or breaks. The RUN indicator is off. Check whether the connection between the LAN/POE port of the combiner and the LAN/POE port is correct. The LAN port indicator is Check whether the connection between the LAN/POE port off. -
Page 11: Legal Declaration
America Parkway, Suite 320 Santa Clara CA 95054. Tel: +1 408.730.6888 13. Legal declaration CIG name, CIG logo, and all CIG product names are trademarks of Cambridge Industries Group Co. Ltd (CIG). All other brand and product names are claimed as property of others respective holders. - Page 12 Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 13 IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
- Page 14 forth for an uncontrolled environment”. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.