Download
Share
Print this page
  1. Manuals
  2. Brands
  3. P2 MOBILE TECHNOLOGIES LIMITED Manuals
  4. Network Router
  5. Z100
  6. Product training

P2 MOBILE TECHNOLOGIES LIMITED Z100 Product Training

Hide thumbs Also See for Z100:

Advertisement

Quick Links

Download this manual
P2 Mobile Technologies Limited -- Confidential
P2 Mobile Technologies
Wirelessing the world ... with no limitation.
Z100 Product Training
Nov-2015

Advertisement

loading

Related Manuals for P2 MOBILE TECHNOLOGIES LIMITED Z100

Summary of Contents for P2 MOBILE TECHNOLOGIES LIMITED Z100

  • Page 1 P2 Mobile Technologies Limited -- Confidential P2 Mobile Technologies Wirelessing the world … with no limitation. Z100 Product Training Nov-2015...
  • Page 2 Table of Content Z100 Hardware introduction (Z100 & POE injector) Basic Configuration Using SmartMoment (Lightweight) Advanced Configuration Using CLI Status Monitoring using Mesh Provision Server P2 Mobile Technologies Limited -- Confidential 13/1/16...
  • Page 3 Z100 Hardware LEDs LAN Port Console Reset DC power USB port Kensington port button connector Lock Slot...
  • Page 4 Z100 status indicated by LEDs Function State - Colour Indication Steady – Green AP power / ready AP is ready status Flashing – Green AP is booting up AP hardware failure No power to AP Steady – Green Network Link Status 1000Mbps Ethernet link negotiated Steady –...
  • Page 5 Explanation of ports and connectors Ports & Connectors Quantity and Specifications LEDs 4 LED indicate different status of AP DC Jack Range: 12 V DC 1A 1 × 10/100/1000 Mbps Ethernet port Ethernet Port PoE input: 802.3af Console A RJ-11 port. Connect the AP to a serial terminal or a laptop for direct local management.
  • Page 6 Z100 – Wall mounting(1) 1. Drive two screws in the wall. The distance between two screws should be 40mm. 2. Align the bracket with screws. 3. Pull down the bracket until it is fastened tightly.
  • Page 7 Z100 – Wall mounting(2) 4. Align the securing hook of the AP with the bracket from up to down until it is locked securely.
  • Page 8 Z100 – Ceiling mounting(1) 1. Secure the ceiling bracket on the ceiling rail and adjust according to the size of the rail. 2. Fasten the bracket with the ceiling rail with a screw.
  • Page 9 Z100 – Ceiling mounting(2) 4. Use the cable-tie 3. Align the securing hook through the locking hole to of the AP with the bracket lock the AP with the (see dotted line), and slide bracket. the AP towards the bracket until the AP is...
  • Page 10 Gigabit PoE+ Injector GE.PW-AT00-00  Optional purchase  For Z100/Z500/X20  802.3at/af Compliant  Output: 54V, 0.65A,  35W (Max.) 1000 Mbps Ethernet,  Full Duplex C8 Appliance Inlet  Excluding power cord  with C7 Connector and Ethernet port)
  • Page 11 Gigabit PoE+ Injector 2 Mounting  holes LEDs  • AC: Green light = power • PORT: Green light = PoE OK...
  • Page 12 Table of Content Z100 Hardware introduction (Z100 & POE injector) Basic Configuration Using SmartMoment (Lightweight) Advanced Configuration Using CLI Status Monitoring Using Mesh Provision Server P2 Mobile Technologies Limited -- Confidential 13/1/16...
  • Page 13 SmartMoment (Lightweight) SmartMoment (Lightweight Mode) is a built-in  configuration tools and virtual controller designed to streamline the process of setting-up a P2 AP. SmartMoment Lightweight mode is for basic  configuration ONLY. You can use CLI for advanced setting. Please refer to the SmartMoment User Guide for ...
  • Page 14 SmartMoment (Lightweight) Use SmartMoment to quickly set up the vanilla AP  (1) From Wireless Power up the AP  Connect to SSID “P2Wifi” with password “p2wtuser”  Enter the IP address “172.16.0.1” in browser  Use default Login Username “p2wtadmin” and ...
  • Page 15 SmartMoment (Lightweight) You can configure the AP to:   Router mode  Access-Point mode  Mesh mode...
  • Page 16 SmartMoment (Lightweight) Router mode   Ability to assign IP to client devices through built-in DHCP service  Network address translation (NAT) between Ethernet port and WLAN Access-Point mode   Add WLAN capability to an existing L2 network  Should connect to a router/hub/switch through an Ethernet cable ...
  • Page 17 SmartMoment (Lightweight) Recommended application Z100 Z500 Router mode Access-Point mode Mesh mode...
  • Page 18 SmartMoment (Lightweight) Sign In Z100:...
  • Page 20 SmartMoment(Lightweight) Overview(1)  Hardware Manager – Firmware version • Model •...
  • Page 21 SmartMoment (Lightweight) Overview(2)  – Network Manager – wan/lan/other generated interfaces – Status – IPv4 address – Uptime in seconds – DNS – Associated interfaces – Virtual interfaces: MAC address...
  • Page 22 SmartMoment (Lightweight) Overview(3)  – Wireless Manager • Radio1/Radio0 • Status • Transmission power in dBm • Channel • DFS: By default on for Radio1 and off for Radio0 • Virtual interfaces • Wireless mode...
  • Page 23 SmartMoment (Lightweight) Overview(4)  Client Manager – Radio0/Radio1 • Radio[].wlan[]s[] – MAC address » Tx in bytes » Rx in bytes » Signal » Noise » »...
  • Page 24 SmartMoment (Lightweight) Overview(5)  – Routes • Destination • Subnet mask • Gateway • Netmask...
  • Page 25 SmartMoment (Lightweight)
  • Page 26 Default configuration – Router mode Z100 is running on Router mode by default  The Ethernet port is bonded with 'wan' interface and set  DHCP SmartIP: When not obtained IP, it is 192.168.1.1/24 The 2 radio are both bridged to 'lan' interface and set static ...
  • Page 27 SmartMoment (Lightweight) – Router mode Network(1)   You can edit network configuration profile for each interface.  The 'wan' is bonded with Ethernet port. Connection Type: DHCP/Static • IP address • Subnet mask • Gateway • Primary and Secondary(optional) DNS •...
  • Page 28 SmartMoment (Lightweight) – Router mode Network(2)   For 'lan' and other additional interfaces, you can edit: Connection Type: DHCP/Static • IP address • Subnet mask • Primary and Secondary(optional) • DNS server DHCP server(optional): Lease time • and IP range...
  • Page 29 SmartMoment (Lightweight) – Router mode Wireless(1)  There is one 2.4GHz and one 5GHz Wi-Fi – card available on Z100 Each radio can support multiple SSIDs – and we provided per-SSID management...
  • Page 30 SmartMoment (Lightweight) – Router mode Wireless(2)   Radio setting is a configuration profile for each single radio card including Radio Status: enable/disable • Wireless mode • Radio0: Mixed  Mode(802.11b/g/n)/802.11N Radio1:  Mixed Mode(802.11a/na/ac)/802.11N/802.11AC Channel •...
  • Page 31 SmartMoment (Lightweight) – Router mode Wireless(3)   SSID setting is a configuration profile for a single SSID include: SSID • Network ID: the network interface bonded • with this SSID Security mode: None/WPA2 • Key: access password • Radius setting(optional): Radius Server, •...
  • Page 32 Mode change on SmartMoment...
  • Page 33 Default configuration – Access-Point mode The Ethernet port is bonded with 'wan' interface and  set DHCP – SmartIP: When not obtained IP, it is 192.168.1.1/24 The 2 radio are bridged to 'wan' interface   Both SSIDs named 'P2Wifi' and uses WPA2 encryption.
  • Page 34 SmartMoment (Lightweight) – Access-Point mode Network(1)   You can edit network configuration profile for each interface.  The 'wan' is bonded with Ethernet port. Connection Type: DHCP/Static • IP address • Subnet mask • Gateway • Primary and Secondary(optional) DNS •...
  • Page 35 SmartMoment (Lightweight) – Access-Point mode Network(2)   Under Access-Point mode, you can add VLAN (need to have trunk port to support VLANs).  The generated interface will be bonded with Trunk port. Connection Type: DHCP/Static • IP address • Subnet mask •...
  • Page 36 SmartMoment (Lightweight) – Access-Point mode Wireless(1)  There is one 2.4GHz and one 5GHz Wi-Fi card – available on Z100 Each radio can support multiple SSIDs and we – provided per-SSID management...
  • Page 37 SmartMoment (Lightweight) – Access-Point mode Wireless(2)   Radio setting is a configuration profile for each single radio card including Radio Status: enable/disable • Wireless mode • Radio0: Mixed  Mode(802.11b/g/n)/802.11N Radio1:  Mixed Mode(802.11a/na/ac)/802.11N/802.11AC Channel •...
  • Page 38 SmartMoment (Lightweight) – Access-Point mode Wireless(3)   SSID setting is a configuration profile for a single SSID include: SSID • Network ID: only 'wan' can be bonded • with SSIDs Security mode: None/WPA2 • Key: access password • Radius setting(optional): Radius Server, •...
  • Page 39 Table of Content Z100 Hardware introduction (Z100 & POE injector) Basic Configuration Using SmartMoment (Lightweight) Advanced Configuration Using CLI Status MonitoringMesh Provision Server P2 Mobile Technologies Limited -- Confidential 13/1/16...
  • Page 40 The P2 Command Line Interface (CLI) is a software  interface to configure and manage P2 Device through terminal under Linux system or PuTTY under Windows system. CLI can provide advanced configuration for:  Network – Wireless – System – Qoss –...
  • Page 41 Use CLI for advanced configuration  (1) Windows Use PuTTY to SSH the IP of AP  Use default Login Username “p2wtadmin”  and Password “p2wtadmin” (2) Linux SSH the IP of AP in terminal  Use default Login Username “p2wtadmin” ...
  • Page 42 Login CLI:...
  • Page 43 You can use CLI for:   Configuration  Troubleshooting  System monitoring...
  • Page 44 CLI - Configuration Common usage of System configuration  – Change the hostname of the AP – Change the timezone of the AP Common usage of Network configuration  – Bond the Ethernet port to the Network interface – Set the IP of the AP –...
  • Page 45 CLI - Configuration Common usage of Wireless configuration  – Set the wireless protocol of the radio card (802.11a/b/g/ng/na/ac) – Set the channel width in 802.11n and 802.11ac mode of the AP – Set the Transmission power (in dBm) of the radio –...
  • Page 46 CLI - Configuration Common usage of DHCP configuration  – Enable/disable the DHCP server function on selected interface – Set the IP pool if enabled DHCP server – Add alternative Default Gateway/DNS server information for Wi-Fi access if enabled DHCP server Common usage of Firewall configuration ...
  • Page 47 Table of Content Z100 Hardware introduction (Z100 & POE injector) Basic Configuration Using SmartMoment (Lightweight) Advanced Configuration Using CLI Status Monitoring using Mesh Provision Server P2 Mobile Technologies Limited -- Confidential 13/1/16...
  • Page 48 Mesh Provision Server The MeshProvision Server is a web-based  configuration and monitoring platform specially designed for P2’s AP. The MeshProvision Server can provide below  functions/features:  AP Configuration (in batch in the future)  Network management  Upgrade firmware ...
  • Page 49 Mesh Provision Server Check the status of the Z100...
  • Page 50 Mesh Provision Server Basic settings  AP configuration – Network • DHCP • Firewall • SSID profile management –...
  • Page 51 Mesh Provision Server Basic settings  – AP configuration...
  • Page 52 Mesh Provision Server AP Firmware upgrade  Manual upgrade – Local; need firmware in hand • Upgrade from P2 server – MPS and APs need Internet connection •...
  • Page 53 Basic procedures for AP deployment Install the AP mounting if applicable  Power on the AP  Use SmartMoment for basic configuration  Use CLI for advanced configuration  Check the AP status with  SmartMoment/CLI/MPS if applicable...