Page 2
IMPORTANT SAFETY INSTRUCTIONS General heed and warnings • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water. • Clean only with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Page 3
• Always use properly rated rigging hardware. for a Class B digital device, pursuant to part 15 of the FCC Rules. These • K-array is not responsible for any rigging equipment and accessories that are not limits are designed to provide reasonable protection against harmful manufactured by K-array.
Page 5
Accessories For Column Speakers User Guide Thank you for choosing this K-array products! To ensure proper operation, please carefully read the owner’s manuals and safety instruction before using the products. After reading this manual, be sure to keep it for future reference.
Accessories For Column Speakers User Guide Unpacking K-JOINT3 Assembling Each K-array product is built to the highest standard and Assembly the hinges to both ends of the column thoroughly inspected before leaving the factory. speaker. Upon arrival, carefully inspect the shipping carton, then examine and test your new device.
Page 7
Accessories For Column Speakers User Guide Lean the loudspeaker against the hinge on the K-FOOT3 B. Rotate the wheel in order to change the joint angle (or against the hinge at the top of a column speaker) and tilt the loudspeakers;...
Accessories For Column Speakers User Guide K-FLY3 Assembling K-PMOUNT Assembling Assembly the K-FLY3 terminal to the flybar. Assembly the K-PMOUNT to the column loudspeaker. For the up-tilting loudspeakers configuration, mount the terminal backward Assembly the hinge to the flybar terminal. Tightening 4 mm hex key sequence...
Accessories For Column Speakers User Guide K-WALL2 Assembling Unscrew the screws of the back plate of the Disassemble the K-WALL2 by removing the lateral plate loudspeaker. You can optionally keep the plate in place. of the bracket to be fixed on the surface. 4 mm hex key Check and set the loudspeaker impedance and SPOT / FLOOD directivity pattern...
Accessories For Column Speakers User Guide K-WALL2L Assembling Match the two parts of the bracket and fix them by assembling the lateral plate of the one attached to the Disassemble the K-WALL2L by removing the bottom wall. screw of the bracket to be fixed on the surface. 5 mm hex key Once properly aimed at the listening position, tighten the blocking screws of the bracket at both the...
Page 11
Accessories For Column Speakers User Guide Unscrew the screws of the back plate of the Match the two parts of the bracket and fix them. loudspeaker. You can optionally keep the plate in place. 4 mm hex key Check and set the loudspeaker impedance and SPOT / FLOOD directivity pattern 5 mm hex key before next step.
Accessories For Column Speakers User Guide K-KBASEFL K-KJUNCT1 Assembling Plug the loudspeaker and fix it to the K-BASEFL. Pass the speaker cable using either the hole on the back or at hole on the bottom of the plate Steadily secure the K-KBASEFL to the supporting surface.
Page 13
Accessories For Column Speakers User Guide Plug the speaker jumper cable to the top speakON Plug the top loudspeaker to the jumper cable and attach connector of the Kobra-KK102 I loudspeaker and the loudspeaker to the K-KJUNCT1 shield. assembly the K-KJUNCT1 to the loudspeaker. Kobra-KK102 I In order to align and connect up to...
Accessories For Column Speakers User Guide K-KBASEFT Assembling Assembly the top shield to the column loudspeaker. Follow the same steps for assembling the K-KBASEFL. Up to 2x Kobra-KK102 I loudspeakers can be aligned on top of the K-KBASEFT using the K-KJUNCT1...
Accessories For Column Speakers User Guide K-KBASETK Assembling Follow the same steps for assembling the K-KBASEFL. Dig a hole on the ground and drive the K-KBASETK in.
Furthermore, the K-KBASE3 allows to install the column loudspeakers on top of the Thunder-KS4 I / KS4P I in vertical position. Assemply the K-FOOT3 on top of the K-KBASE3. Use the joint to attach the column loudspeaker.
Page 17
Accessories For Column Speakers User Guide Remove the four rubber feet from the K-KBASE3 Assembly the K-FOOT on top of the K-KBASE3. Fix the K-KBASE3 with four M8 screws on top of the subwoofer.
Accessories For Column Speakers User Guide K-KBASE3 390mm 15,4in...
Page 24
Designed and Made in Italy K-ARRAY surl Via P. Romagnoli 17 | 50038 Scarperia e San Piero - Firenze - Italy ph +39 055 84 87 222 | info@k-array.com www.k-array.com...