PIKO 36233 Manual

SUSI - Bank
CV
(CV 1021)
4 918 Volume - Station Announcemen
919 Volume - Oiling the Side Rods
920 Volume - Heavy Load Sound
921 Volume- Light Switch Train Light
922 Volume - Clickety-Clack
923 Volume - Curve Squeal
924 Volume - Rail Creaking
925 Volume - Light Switch Cab Light
926 Volume - Break Squeal
927 Volume - Direction Switch
928 Volume - Light Switch Chassis Lights
929 Volume - Light Switch Lighting for driver's desk
900 - 931 Function key assignment (function mapping) of the
8
individual sounds
900 Function key - Motor
901 Function key - Horn
902 Function key - Battery Main Switch
903 Function key - Cab Door
904 Function key - Cab Window
905 Function key - Windshield Wipers
906 Function key - Switching Gear
907 Function key - Hand Brakes
908 Function key - Compressor
909 Function key - Preheater
910 Function key - Sanding
911 Function key - Radio Chatter 1
912 Function key - Radio Chatter 2
913 Function key - Coupling
914 Function key - Engine Room Door
915 Function key - Radiator Grill Open/Shut
916 Function key - Oil separator
917 Function key - Fuel Pump
918 Function key - Station Announcement
919 Function key - Oiling the Side Rods
921 Function key - Light Switch Train Lighting
922 Function key - Clickety-Clack
923 Function key - Curve Squeal
925 Function key - Light Switch Cab Light
928 Function key - Light Switch Chassis Lights
929 Function key - LLight Switch Lighting for driver's desk
PIKO Spielwaren GmbH
Lutherstr. 30
96515 Sonneberg
GERMANY
Description Value Range
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 255
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
0 - 28
#36233 PIKO Sound module
Factory
default
with loudspeaker for BR 106 G
150
The Sound module with loudspeaker for all
150
PIKO loco decoders with SUSI Interface
130
100
255
255

1. Characteristics

60
• Intelligent Sound control with 480 second Sound buffer
100
• High-resolution Sound: 22050Hz Samplerate, 12bit
150
• Efficient output final stage for 4-8 Ohm loudspeaker
50
• Generates the operating sounds of the locomotive and brake squeal
100
• Sound is specially adjusted to the body of the locomotive for best resonance
100
• Simultaneous rendition of 8 independent sound channels
• Additional adjustable sounds like e.g. horn, sanding, or own custom sounds
• Function Mapping up to f 28
1
• With smart start function: The Sound module stops the locomotive decoder, when starting until the vehicle's engine
2
synchronize with the sound.
9
• Separate adjustable volume for almost all sound events (only DS4)
16
• Muting with fade in and out function
17
• Volume control via potentiometer
21
• Analogue operation with start-up and shut-down noises, when used with a suitable decoder
7
12

2. Description

11
The PIKO Sound module provides digital original sounds from the original locomotive with a resolution of 12 Bit and a sam-
10
pling rate of 22,05 kHz. The intelligent sound control adapts the sounds to the respective driving situation. For example, when
14
driving uphill or downhill, the sounds are reproduced according to the current engine load. If the driving noise is switched on
22
via a function key, the upgrade phase of the locomotive can be heard first. If the locomotive is to start up, the sound module
23
stops the locomotive engine until the vehicle starts up synchronously with the sound. If the locomotive is stopped, the train
13
brake squeals.
15
If the driving noise is switched off when the locomotive is stationary, a corresponding dismantling phase can now be heard,
20
including the closing of the door when the driver leaves the driver's cab. Thanks to the 8-channel technology, the locomotive's
19
driving noise and other locomotive-specific noises can be switched on simultaneously using special function keys. These are
18
horn, sanding and other additional noises, depending on the type of locomotive. These can be called up using the function
8
keys F0 - F28. If the locomotive leaves the visible area of a model railway system, e.g. into the staging yard, the "Sound
24
off" function can be used to softly fade out the entire locomotive sound using the special function key. Nearly all sounds are
3
separately adjustable in volume via CV programming and can be assigned to any special function key up to F28.
25
In combination with a correspondingly suitable locomotive decoder the IntelliSound 4 module can even be in analogue mode
26
with start-up and shut down sounds.
4
5

3. Installing a Sound Module

6
SUSI interface
Insert the SUSI plug into the SUSI socket of your decoder. The sound module is supplied with power and data from the
decoder.
Loudspeaker
Install the speaker in the bracket provided in the locomotive (see operating instructions for the locomotive, page 13) and
connect the speaker cables to those of the sound module.
Fastening the Sound module into the Vehicle
Using the double sided adhesive pad provided, affix the decoder to the desired location in the locomotive. The adhesive pad
protects the decoder from coming in contact with conducting surfaces and holds it in place.
Please note that according to the EMV laws the component may only be operated in vehicles that carry the CE symbol.