Victor VLINK V450 Startup Manual

VICTOR
%INK
START.U
P
GUIDE
Latch
Trough
Power
Button
Bait Cup
Chamber
LED
Indicator
Light
Button
Outer Case
Battery
Compartment
Victor'VL|NK"
Mouse Trap
Model:V450 I Victor'VLINK"
Rat Trap Model:V46o
FCC:
this device
complies with part t5 of the fcc
rules. Operation is subject to the following two
conditions: (t)this
device may not cause harmful interference, and
(2
this device must accept
any
interference
received,
including interference that
may cause undesired operation.
Warning: Changes
or modifications to this
device
not
expressly
approved
by
Woodstream
Corporation could
void
the users authority to operate the equipment.
Note:
This equipment
has been tested and
found to comply with the limits for
a Class B digital
device,
pursuant to
Part tS of
the
FCC Rules.
These limits
are
designed to provide
reasonable
protection against harmful interference in
a
residential
installation.
This equipment generates,
uses, and
can radiate radio frequency energy
and, if
not installed
and
used in
accordance
with
the instructions, may
cause
harmful interference to radio communications.
However,
there
is
no guarantee that interference will not occur in
a
particular installation. lf this equipment
does
cause
harmful interference to radio
or
television
reception,
which can be determined
by
turning the equipment off
and on,
the
user is
encouraged to try to correct the interference
by
one or more of the following
measures:
.Reorient or relocate the receiving
antenna.
. lncrease
the separation between the equipment
and receiver,
.Connect.the equipment into
an
outlet on
a
circuit different from that to which the
receiver is connected.
.Consult the dealer or
an experienced radio/TV technician for help.
lC:
This
device
complies with lndustry
Canada's
licence-exempt
RSSs.
Operation
is
subiect to the
following two conditions:
(1)This device
may not
cause
interference; and Q)This device must
accept any interference, including interference that may
cause
undesired operation of the device.
RF
Exposure: This equipment complies with
FCC and lC
radiation exposure limits
set
forth for
an
uncontrolled environment. This equipment should
be
installed and operated with a minimum
distance of 20cm between the radiator and your body.
WARNING: Electric Shock and Spark Hazards. lgnition:
Do
not
use
near unvented flammable
vapors, liquids, or combustible solids. Do not use in barns, stables, or similar wet or dusty
locations. High
Voltage:
Keep out of reach of children and pets. Use only dry hands or rubber
gloves
to
handle. Power OFF and bait. Do not touch metal plates when device is
powered
on.
Electromagnetic Waves:
Keep
pacemakers
and
life support
devices
at
least
one foot
away.
Consult
your heart doctor
if
you receive
a shock. Failure
to read
and
heed
all
warnings
and
directions may
cause
electric
shock, fire,
or
serious injury. Read and
follow
all label
instructions.
Manufactured
for:Woodstream Corporation
69 N. Locust Street, Lititz, PA 17543.800-800-1819
Trap
Lid
Pak
Before you start: Confirm you have
a
VLINK" account
and are able to successfully log in at www.vlinkhq.com.
t. Open
the outer
case
to
access components.
When outer
case
lid
is
open, trap
is
disengaged.
2.
Remove the kill chamber.
3.
Slide out
the power
pak.
4.
Open the battery compartment on the bottom
side
of the
power pak and install the 4"AA" lithium batteries
(included).
5.
Using a
Philips
head screw driver secure the battery
compartrnent lid to the power pak with the
Z
screws
provided.
6.
Reinstall the power pak.
7.
Reinstall the kill chamber
o"@
2.
BAITING
Option
A
t. Remove bait cup.
2.Place
your
preferred solid
bait
in
the bait trough located on
the
top
side
of the kill chamber.
3. Replace bait cup.
Option
B
t.
Open bait cup and insert sticky
or liquid bait into designated
bait area.
z.
Replace
bait cup.
t. Plug in the VLINKTM hub.
lf you
are
planning to
use
your local network, plug
your ethernet cable
into the ethernet
Port.
For all
other
hub
instructions, refer
to the online
setuP
guide at www.vl
inkhq.com/instructions.
t. Download the
VLlNK"
app
from the Apple or Google Play Store.
2. Launch
the
app and
follow the on-screen instructions
to
connect your
trap to the
app.
t.
Once your trap
has
successfully connected, close the
lid-and the trap
is set!
z. Place
traps indoors or outdoors.
3.CONNECTING
4.
DOWNLOADTHEAPP
6.
GET
ITON
P
googlePlay
S.SETTRAP
kill
to
remove any debris.
1.
BATTERY
I
NSTALLATION
\
tl -/