Advertisement
Quick Links
Advertisement
Related Manuals for Patiova Olympus
Summary of Contents for Patiova Olympus
- Page 1 Olympus Playset ASSEMBLY MANUAL PATIOVA.COM 610-857-1359 6649 North Moscow Rd Parkesburg, PA 19365...
-
Page 2: Tools Required
Thank you for your Patiova Playset Purchase. We are excited for the great times and memories you will share while enjoying your new Patiova playset. Let’s gets started on the assembly!! This manual is designed to simplify the assembly process with step-by-step instructions and pictures to help along the way. - Page 3 Hardware 5/16 x 6” Bolt 5/16 x 4 1/2” Bolt 5/16 x 4” Bolt 5/16 x 5” Hex Head Lag 3” Star Head Lag 3” Wood Screw 1 3/4” Washer Head Screw 1 1/2” Poly Screw 1 1/2” Wafer Head Lag 5/16”...
- Page 4 Step 1. Step 2. Begin the assembly by locating these components. Start the assembly with the rock wall and a 68” 2x8. Step 3. Step 4. Place the 68” 2x8 on the bottom of the rock wall and center it. Place a 4x4 brace at each end of the 68”...
- Page 5 Step 5. Step 6. The cargo net should shipped assembled. Place the floor section on one of the side walls as shown above then center the wall between the floorboards. Step 7. Step 8. Fasten the floor section to the side wall using 3” star head lags Place the other side wall on the floor section and use the same through the inside 2x6’s.
- Page 6 Step 9. Step 10. Place the tower upright then locate two 46” 2x6’s and place them Place two 59” 2x4’s on either side of the 2x6 railings and fasten between the two side walls on the outside of the 4x4 posts. them using 3”...
- Page 7 Step 13. Step 14. Raise one side of the floor section and place the cargo net Fasten the ladder using two 3” star head lags through the side 2x8 underneath. and one 3” star head lag through the top of the 4x4 post. Step 15.
- Page 8 Tarp Roof Step 1. Locate two 2x4’s with half moon pieces attached and place them on the 2x6 railings with the half moon pieces facing out. Fasten these 2x4’s with 3” wood screws. Step 2. Step 3. Place a 59” 2x4 on top of the other 2x4’s and center it. Place the tarp roof over the wood frame and stretch it to fit.
- Page 9 Wood Roof Step 1. Locate the two side panels. Step 2. Step 3. Place the panels together then fasten the tops together using 3” Locate the sunburst pieces. wood screws.
- Page 10 Step 4. Step 5. Place the sunburst pieces on the inside of the wood roof and Place the wood roof on the tower as shown then fasten both sides fasten them with 2 1/2” wood screws. with 1 1/2” wood screws. Completed Wood Roof...
- Page 11 Standard Swing Frame Step 1. Locate the swing beam and place it on the ground with the pre-drilled bearing holes facing up. Step 2. Step 3. Fasten the swing bearings to the swing beam with the included If your playset has a glider, place the glider bracket on the swing lags in the pre-drilled holes.
- Page 12 Step 4. Step 5. Place two 4x4 posts at the end of the swing beam. Place a T-Nut in each pre-drilled hole on the 4x4 posts. Use a hammer to set them in the wood. Step 6. Step 7. Flip the posts over so the T-Nuts are on the bottom then line Place the 2x6 end piece on the posts.
- Page 13 Step 8. Step 9. Fasten the 2x6 to the posts using a 4 1/2” bolt and washer Raise the end of the swing frame up and move the 4x4 legs down Thread the bolt into the T-Nut below then use a 1/2” wrench or into place.
- Page 14 Step 12. Step 13. Place the 2x4 end piece on the 4x4 posts and line it up with the Lift the swing frame up and place it on the tower next to one of posts. the 4x4 posts. Fasten it with 3” wood screws. Step 14.
- Page 15 Step 16. Step 17. Fasten the swing beam to the post using a 6” bolt and washer Attach the rest of the swings to the swing bearings to finish the through the hole. swing frame. Space Saver Swing Frame Note: If your playset has a space saver swing frame the tower will have two extended 4x4’s as shown in the illustration above.
- Page 16 Step 1. Step 2. Locate the two swing beam sections. Place the two swing frame sections together and fasten them with four 2 1/2” wood screws. Step 3. Step 5. Place the swing frame on the tower against the inside of the Fasten the swing beam to the 4x4 posts using four 6 1/2”...
- Page 17 Accessories Step 6. Hang the swings from the swing beam to complete the space saver swing frame. Tire Swing Tire Swing Place the tire swing bracket on the center of the floor joist then Hang the tire swing chains from the brackets using the included fasten it with two hex head lags.
- Page 18 Wave Slide Wave Slide Place the slide on the tower above the ladder. Fasten the slide with 1 1/2” wafer head lags. Sidewinder Slide Sidewinder Slide Place a 2x4 and two 2x6’s in the opening to support the Place the assembled slide on the tower and fasten it with the sidewinder slide.
- Page 19 Wood Ladder Wood Ladder Place a 30 7/8” 2x4 behind one of the slats on the front of the Place the ladder in position and fasten it with 2 1/2” wood screws. playset. The opening should be 19 1/4” between the 2x4 and the 4x4.
Need help?
Do you have a question about the Olympus and is the answer not in the manual?
Questions and answers