Download Print this page

Advertisement

AMP-F2 立体声功放
Stereo AMP
Starke Sound Inc.
17810 S.Main St., Suite B, Gardena, CA 90248
starkesound.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the eversolo AMP-F2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Starke eversolo AMP-F2

  • Page 1 AMP-F2 立体声功放 Stereo AMP Starke Sound Inc. 17810 S.Main St., Suite B, Gardena, CA 90248 starkesound.com...
  • Page 2: Table Of Contents

    Content/ 目录 Introduction Hardware Downloads 产品简介 性能参数 硬件端口介绍 资源下载...
  • Page 3: Introduction

    Work with united Strengh of Starke Sound’s team and Eversolo's team, base on Starke Sound NS600 amp module, raising its sampling rate to 600 kHz and further reducing noise with a newly designed SAPS switch mode power supply of 600 watts.
  • Page 4 11KΩ Input Impedance (XLR) 22KΩ Input Sensitivity 2.7V Output terminals 2 pairs beryllium copper binding post custom made by Starke Sound Output Impedance 0.136Ω(5 Hz to 100 kHz) Minimum load impedance 0.8Ω True balance circuit Heat 65 BTU / hr...
  • Page 5: Hardware P3

    STEREO AMP Hardware Rear Panel ⑤ ⑦ ⑨ ⑧ ① ② ③ ④ ⑥ Descriptions: ① Power on /off ② Power input plug (Warning: Please carefully check the input power voltage setting before inserting the power supply, adjust to the position suitable for the local voltage, and replace the corresponding fuse with proper specifications, the power amplifier could burn with incorrect fuse! Use a 3.15A fuse at 220V-240V, or a 6.3A fuse at 110V-120V) ③...
  • Page 6 STEREO AMP Front Panel Indicator light Switch Controls Short press: Power on/Power off/Reboot/ Indicator light: In standby mode, the indicator light is orange. In working state, the indicator light is white. Page 4...
  • Page 7 STEREO AMP Set-up instructions For standard mode, set this switch to STD (standard). For bridge mode, set this switch to BRIDGE. Connect your 2 input channels using either unbalanced (RCA) or balanced (XLR) cables. Channels are labeled 1 and 2. Set the two toggle switches to UNBAL (unbalanced) or BAL (balanced) as appropriate.
  • Page 8 STEREO AMP Connect your two speakers to the output binding posts: 1 and 2. Speaker wires can be terminat- ed with “banana plugs” which are inserted, or stripped insulation (unscrew binding post cap, insert wire into hole on threaded shaft and tighten cap). Observe correct polarity (“+” red and “-”black).
  • Page 9: Downloads P7

    STEREO AMP Downloads For more tutorials, please visit www.eversolo.com, please visit the Downloads page on official website and scan QR code. Wechat Subscription Safety instructions 1) Read, follow and keep these instructions 2) Do not remove the cover as repairs require qualified technicians 3) Do not use the product near water 4) Do not install near any heat sources such as radiators, heaters, stoves or amplifiers 5) Clean the product only with a damp cloth...
  • Page 10: 产品简介

    立体声功放 产品简介 高品质 高效率 一切都是为了真正的高品质声音。 AMP-F2由Starke Sound团队与Eversolo团队通力合作,基于Starke Sound团队开发的创新的 NS600模组,拥有高达600KHz的采样率。同时通过新设计的SAPS音频专用开关电源来显著 降低噪音,提升动态表现。 采用高效率的D类放大结构, 同时最大程度的优化电路来提升音质表现。AMP-F2是可桥接的, 所以在需要2声道或者单声道的时候灵活配置。 与Eversolo DMP-A6厚度和宽度完全一致,并在信号通路搭配上进行优化。AMP-F2是DMP-A6 的最佳搭配,也是价值和性能的完美结合。 使用本机器之前建议您先阅读本说明,以便您正确使用产品的所有功能。 第 8 页...
  • Page 11: 性能参数

    >110dB, A计权, 4 ohm 250W 0.003% 10W at 1KHz 输入接口 2声道RCA输入 2声道 XLR输入 输入阻抗 (RCA) 11KΩ 输入阻抗 (XLR) 22KΩ 输入灵敏度 2.7V 输出接口 2对铍铜喇叭端子 Starke Sound定制 输出阻抗 0.136Ω(5 Hz to 100 kHz) 最低负载阻抗 0.8Ω 全平衡电路 是 发热量 65 BTU / hr 风扇噪音 无 整机功耗...
  • Page 12: 硬件端口介绍

    立体声功放 硬件端口介绍 后背板 ⑤ ⑦ ⑨ ⑧ ① ② ③ ④ ⑥ 接口说明: ① 电源开关 ② 电源插座/保险丝 警告:请在插入电源之前仔细检查输入电源电压设置,调到适合当地电压的位置,并换上对应规格 保险丝, 否则功放可能会烧毁!220V-240V电压下使用3.15A保险丝,110V-120V电压下使用6.3A保 险丝。 ③ 电压切换 ④ 输出端子,用来连接扬声器接线柱 ⑤ XLR和RCA模拟输入 ⑥ XLR输入和RCA输入切换开关 ⑦ 桥接开关(STD为标准模式,BRIDGE为桥接模式。桥接模式下,仅斜线区域的输入输出在工作状 态。) ⑧ 触发输出(可以和有触发功能的后级联动) ⑨ 触发输入(可以和有触发功能的前级联动) 第 10 页...
  • Page 13 立体声功放 前面板 指示灯 开关按钮 开关控制 短按: 开机 / 选择关机 / 重启 指示灯: 待机状态下,指示灯为橙色。 工作状态下,指示灯为白色。 第 11 页...
  • Page 14 立体声功放 设置指令 在标准模式下,将这个开关设置为STD(标准)。桥接模式下,将这个开关设置为BRIDGE(桥接) 使用非平衡(RCA)或平衡(XLR)电缆连接2个输入通道。通道被标记为1和2。将2个拨动开关设置为对 应的UNBAL(非平衡)或BAL(平衡)。 第 12 页...
  • Page 15 立体声功放 将两个扬声器连接到输出接线柱:1和2。扬声器线可以用香蕉插头或剥去绝缘的裸线(拧下接线柱帽, 将线插入螺纹轴上的孔中并拧紧帽)进行连接。观察正确的极性(红色“+”和黑色“-”)。 将电源线连接到交流输入端,墙壁插座。请留意电压和当地区域一致。然后将开关置于ON 位置, 接通放大器的电源。 功放可以通过前面板按钮进行开启/待机,也可以通过触发线自动开启/待机。 TRIGGER IN 插口连接配备 TRIGGER OUT插孔的设备时,可通过上游相连设备的联动操作控制本机 的电源开启/待机。 TRIGGER OUT 插口连接配备 TRIGGER IN 插孔的设备时,可通过本机的联动操作控制下游相连设备 的电源开启/待机。 TRIGGER IN/OUT 插孔 输入/输出最大 12V DC/150mA 电气信号。 TRIGGER模式下,前面板开关按钮将无效,开关由Trigger来控制。 第 13 页...
  • Page 16: 资源下载

    立体声功放 资源下载 更多教程,请访问官网:www.eversolo.com,点击下载页面或扫描二维码。 微信公众号 安全警示: 1)阅读、遵守并保存这些说明 2)由于维修需要合格的技术人员,请勿拆卸盖子 3)不要在靠近水的地方使用 4)不要安装在任何热源,如散热器,加热器,炉灶或放大器 5)仅用湿布清洁产品 6)举起或移动此沉重产品时要小心 7)防止电源线被踩到或夹到 8)在雷雨天气或长时间不使用时拔掉电源 9)确保产品上没有放置花瓶等装满液体的物体 有限保修 自购买之日起1年 (保存原始发票,以便通过经销商安排维修。如果您在网上购买您的放大器,请直接联系我们。) 第 14 页...