Page 1
LED COLOUR TV MAINTENANCE MANUAL MODEL: LS09C CHASSIS Please read this manual carefully before maintenance.
Page 2
CATALOG Chapter1:Safety and notes....................3 Chapter2: TV specifications and ports functions ............4 Chapter3: Software upgrade tooling,software upgrade instructions,software initialization,parameter setting,software version and screen matching instructions..6 Chapter4:Repair process and examples of typical accident........11 Chapter5: Factory model parameters setup instructions and precautions....16 Chapter6:Instructions of simple factory debugging specification ......19...
Chapter1:Safety and notes 1-1 Installation notes (1) Please don't beat or rub, scratch the surface of the LCD screen heavily, don’t touch it with hand casually. (2) When the screen is dirty, please clean it with absorbent cotton or cotton cloths lightly. (3) Please clean it timely when water or other viscosity pollution fall, which may make the LCD face or color change.
Chapter2: TV specifications and ports function (The parameters are for reference only, the specifications should 2-1 Basic specifications accord to practicality of the batch orders)...
Page 5
2-2 Introduction of ports(practicality photos) ATTENTION: 1. HDMI and YPbPr support to 1080P; 2.The recommendation resolving ratio of VGA is 1024X768; 3. Av output supports TV input /AV output,Av input /AV output; 4.The picture is for a reference only,the actual item is the standard.
Chapter3: Software upgrade tooling , software upgrade instructions , software initialization , parameter setting , software version and screen matching instructions 3-1 Software upgrade tooling there are two kinds of using upgrade tooling: 1.Use the combined interface(the parallel port) upgrade tooling :use the upgrade program: ISP_ Tool V4.0.5.exe(and higher versions)...
Page 7
Cancel the selection in the red line frame of last chart , as following shows: 3.Select(connect)first ,if normal ,system will feedback the flash style of the machine chassis As following...
Page 8
4.Select the toolbar on the "Read", then click on the bottom there's "Read", select the upgrade file, such as "CH-P06U (VC)-V1.15-YD12.bin" 5. select "Auto", and check the options according to the following chart...
Page 9
6. Select the top of the "Connect", if connected, there will be "Device Type" prompt, select "OK" and then click "RUN", After the upgrade is complete, the green "PASS" prompt will appear in the progress bar below...
Page 10
3-2-2 USB Upgrade 1) The first method Copy the file to root catalogue of USB, The filename has to be for "bin_6m181. bin".Turn on the TV, Insert the USB flash , .Entre the menu to choose "Sotfware Update(USB)", And press key "ENTER"...
Page 13
4-5 Audio Trouble(No sound) 4-6 Function Trouble(TV video)...
Page 14
4-7 Function Trouble(PC) 4-8 Function Trouble(SCART、HDMI、YPbPr、DVB/TV)...
Page 15
4-9 When you meet the following common problems, you might diagnose and get the solutions without contacting with the technicians. Symptoms Possible Reason Solutions No picture, no sound, and no 1.The power cord is not plugged in 1.Plug in the power cord indicator light on 2.The power is off 2.Turn the power on...
Chapter5: Factory mode parameter setting instructions and notes 5-1 Enter into the factory mode Switch on TV set, and make it works normally: 1.Press 【MENU】 key on the remote control 2.Press number keys “1”、 “1”、 “4”、 “7” on remote control to enter password. Finish entering the factory mode.
Page 17
1.W/B ADJUST(Usually used): Going to the white balance adjusting page. 2.PICTURE MODE: To change Parameters for different picture mode like mild worm… 3.Sound Mode :To change Parameters for different sound mode like standard music … 4.Volume curve :To change the volume page.note:the volume curve mode should not set here WHITE PATTERN Press to generate 6 kinds of output pattern like white red…...
Page 18
1.PQ NONLINEAR (Usually used) MODE: Channel PICTURE MDOE: Mostly we set it to standard Brightness Curvel: To change the brightness page Contrast Curve: To change the contrast page Saturation Curve: To change the saturation page Hue Curve: To change the hue page Sharpness Curve: To change the sharpness page Volume Curve: To change the volume page All the CURVE are almost the same, so I only show Brightness curve as sample: Usually...
Chapter6:Instructions of simple factory debugging specification 6-1 Clear EEPROM ,and set the parameters after upgrading according to the upgrade instructions. 6-2 Check each channel/source to see if the image and sound are normal.
Need help?
Do you have a question about the LS09C and is the answer not in the manual?
Questions and answers