Subscribe to Our Youtube Channel
Related Manuals for zapco ST-X III Series
Summary of Contents for zapco ST-X III Series
- Page 1 ST-X III SERIES Owner’s Manual Before operating the unit, please read this manual throughly and retain it for future reference.
-
Page 2: Table Of Contents
Table of Contents General instructions IT Istruzioni Generali DE Allgemeine Anweisungen FR Instructions Générales ES Instrucciones Generales CH 常规安装指引 Class, Power, Heat All wire is not created equal Amplifier Controls Speaker Wiring Technical Specifications... -
Page 3: General Instructions
• La borne entre l'alimentation principale (+12V B) et la Zündeingang +12 (REM) und kann an die accessorio (ACC) masse (GND) est l'entrée de mise sous tension +12 (REM) Mounting your Zapco amplifier is easy. Just keep in mind a Zündausgangsleitung des Hauptgeräts angeschlossen few guidelines: Installare l’amplificatore werden. -
Page 4: Instrucciones Generales
能性, 并降低系统的动态范围. 如果您的主机输出不足, 最 creación de energía genera calor y la para la refrigeración 好购买信号放大器以向功放机提供更多信号, 从而获得更 down... and possibly be damaged. Zapco offers both Class A/B and Class D amps. Class A/B for the se requiere aire 好的音效. user who puts sound quality and dynamics first, and Class D for the user who wants big power in •... -
Page 5: All Wire Is Not Created Equal
All Wire is not created equal Wire Size Do not use CCA wire with Zapco amplifiers The second most common cause of under performing amplifiers is insufficient power current or a poor power connection. The most common cause of under performing amplifiers is insufficient It is easy to think of wire as just wire but the fact is there are major differences between the types ground current or a bad ground connection. - Page 6 ST-X SQ III Input/Controls ST-X Mono III Input/Controls The ST-X SQ III amplifiers have similar functions, but different layout puts the controls in different The ST-X Mono III amplifiers have similar functions and share the same input panel. Showen here is positions.
- Page 7 Strapping the ST-X Mono III Strapping the Ouputs of the ST-X Mono III The ST-X Mono III amplifiers are true mono units and you can double their power by “strapping” two units of the same model together to drive a single voice coil. Always keep in mind that each amp must see a minimum load of 2 Ohm (1V per amp).
-
Page 8: Speaker Wiring
Speaker Wiring of the ST-X SQ III Amplifiers 2-Ch. Amplifier - 3-Ch. Mode It is possible to run the 2Ch amps in “3-Channel” mode by running a pair of speakers for the mids and highs on left and right channels, and at the same time run a woofer bridged between the L+ The Very Basics and R- terminals as shown. - Page 9 4-Ch. Amplifier - Stereo Mode 4-Ch. Amplifier - 5-Ch. Mode A simple 4 channels hookup for a right and left stereo pair. A 3-way system with front stage, rear stage and subwoofer in mixed mono configuration. The 5-speakers system requires a passive crossover between the front highs and the mono woofer, with capacitors on the front highs positives and a coil on the woofer positive.
-
Page 10: Technical Specifications
2 OHM MIN/CH APEX GROUP - APEX Business Development (ABD) CO LTD, Bright Way Tower, office 04 7/Fl, 33 Mong Kok Road Kowloon City, Hong Kong 999077 fb.com/zapcocaraudio instagram.com/zapco_official ZAPCO is a brand of APEX Group © All rights reserved... - Page 11 Modesto, California USA Since 1974 zapco.com...
Need help?
Do you have a question about the ST-X III Series and is the answer not in the manual?
Questions and answers