Table of Contents
Advertisement
You can adjust a selected colour
individually and save and retrieve under
the PICTURE MODE
setting. Press the
COLOR MANAGEMENT
button to open
the menu
Select a menu item and the ◄ ► to adjust
each item level.
• The result box is displayed on the right of the
cursor and shows the adjusted colour.
PROFILE
LOG
PROFILE SAVE
M l I Ml I—
^4-.RETUBN
seuct-BU^
DEFAULT_
Create a new profile
Adjusting the selected colour
Select a colour and adjust
COLOUR, TINT
and
BRIGHTNESS
Select the
CURSOR
menu and press
enter
• The projected image is captured, and the target
cursor is displayed.
• When the
LOG
is fully stored, the target cursor
will not be displayed. See "Managing stored
logs" on page 27.
Target cursor
/V"]n'T%i, t' ,
Y MSS§y\\
Adjusted colour
COLOUR
BRIGHTNESS
-V
\ '—-JKk
Adjust the vividness of the colour
Setting range: -30 to +30
Adjust the colour tone.
Setting range: -30 to +30
Adjust the brightness of the colour.
Setting range: -20 to +20
wmm
2. Move the cursor with A T ◄ ► to the
required place to select a colour and press
ENTER.
• The colour at the centre of the target cursor is
sampled and the sample box is displayed on
the left of the cursor. The menu items are
displayed on the upper part of the screen.
Mg
.n-fault
Sampled colour
Press ENTER to store the adjusted result.
• "PROCESSING"
is displayed for a few seconds
and the result is stored in
LOG.
• You can store up to 8 logs under
LOG
for each
PICTURE MODE
setting.
Press MENU or RETURN to return to the
previous menu.
• Repeat the steps above to store more
adjustment.
26
-
English
Remote control operation
Ii11iT»
(*] i-I* I L*l*
i
You can edit or delete the stored logs of the
selected PICTURE MODE.
1. Select LOG and press ENTER.
• The LOG menu is displayed.
PICTURE MODE : CINEMA 1
ng
ofile
iE
setting, y<
the
PROFIL
ct the reau
s
ENTI
I§ 1 t j Oil
and select the PROFILE menu.
• The profile settings of the selected PICTURE
MODE will be displayed.
3. Select the required profile and press
ENTER.
NORMAL
Sampled colour—Adjusted colour
USER1
Select the required log from 1 - 8 or ALL
DELETE, and press ENTER.
• Select
CHANGE
to edit the log.
The cursor menu is displayed and you can
readjust the colour.
• Select
DELETE
to delete the log.
The confirmation screen will be displayed.
Select
OK
to delete.
• When you select
ALL DELETE,
the
"DELETE
ALL LOG."
screen is displayed. Select OK to
delete all logs. The
PROFILE
setting will be set
to
NORMAL.
Saving a log setting as a profile
Return to the
COLOUR MANAGEMENT
menu
and save the stored log as a profile. Make sure that
the
PICTURE MODE
is not switched.
Select the PROFILE SAVE menu and press
ENTER
• The
PROFILE SAVE
menu is displayed. You
can save the profile as
USER1, USER2
and
USER3.
USER2
USER3
Return to the default setting of the
PICTURE MODE
Defined profile settings.
NOTE:
• LOG and PROFILE SAVE are not displayed
before you apply COLOUR MANAGEMENT.
• If you load a profile with a different attribute mode
of the profile, the CURSOR and PROFILE SAVE
menus will not be displayed.
• The approximate colours will be adjusted at the
same time. If you adjust the exact same colour
differently, both colours will affect each other and
you might get unexpected results.
• White, Black and Grey are not adjustable.
• If you escape the COLOUR MANAGEMENT
menu or attempt to perform another menu action
before you save the adjusted profile, the
confirmation screen will be displayed.
• If you switch the input signal before you save the
profile, the setting will be cancelled without notice.
2. Press ENTER to save the profile
• The confirmation screen is displayed, Press
ENTER
again to save.
English - 27
Advertisement
Table of Contents
