Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Videx B100-SA v2
Summary of Contents for Videx B100-SA v2
- Page 1 B100-SA Standalone Biometric Reader INSTALLER’S MANUAL...
-
Page 2: Table Of Contents
INDICATION WIRING ..........................ADDING ADMIN FINGER ......PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT ............Pairing B100-SA v2 with DINRTT ............Pairing B100-SA v2 with RTT ............Pairing B100-SA v2 with RU2 ADMINISTRATOR PROGRAMMING ......................... ADD Finger Relay 1 .............. -
Page 3: Introduction
-10ºC or/and if the sensor could only be exposed to direct sunlight, it is strongly recommended to install the reader inside a third party sealed wall mount box (fitted with additional heater if very low temperature) to keep a constant sensor level performance. Videx™ cannot guarantee the functionality of the product if measures and advice before are not followed. -
Page 4: Specifications
Current Consumption: 100 mA max. Power Supply: 9-14 V DC Indication: Tricolor tatus LED IP Factor: IP65 Storage/Operating Temperature : B100-SA v2 -20°C to +50°C Storage/Operating Humidity: 5% to 93% RH without condensation Dimensions(mm): APPLICATION DIAGRAM DINRTT (Op onal) (Op onal) -
Page 5: Wiring
WIRING Colour Connection 12V DC 12V DC Black Black Pink RS485 Green Tamper Violet Tamper Blue Blue Tamp Push Button Orange Green A (RS485) Pink Orange B (RS485) Violet Gray Grey Yellow Relay Yellow (2A) White White 12VDC POWER SUPPLY Black Pink Violet... -
Page 6: Pairing - Biometric Reader And Remote Relay Unit
If secure installation is needed, the reader can be connected to remote relay unit at secured area, which also can play the role of request-to-exit push button. Follow the instructions bellow to pair(couple) both devices or refer to the Remote Relay’s Manual. Pairing B100-SA v2 with DINRTT 12 VDC... -
Page 7: Administrator Programming
ADMINISTRATOR PROGRAMMING Use point fingers as Administrator and Installer. You can use the other fingers as access fingers. Administrator finger is enrolled at the end of the system installation. Initial enrollment of the Admin finger is described in installer manual. RIGHT LEFT ADD Finger Relay 1... -
Page 8: Delete All Fingers
DELETE ALL Fingers Action Finger Backlight Buzzer Sound Swipe Admin Finger 4 times short beep slow blinking short beep Wait 5 seconds slow blinking (until fast blinking) multiple beeps Swipe Admin Finger 2 times fast blinking CHANGE ADMIN Finger Action Finger Backlight Buzzer Sound... -
Page 9: Installer Programming
INSTALLER PROGRAMMING Set Relay 1 Time Action Finger Backlight Buzzer Sound Swipe Installer Finger 1 time short beep slow blinking short beep Wait 5 seconds (until fast blinking) Swipe the INSTALLER Finger fast blinking beeps on 1 second and start counting seconds Swipe the INSTALLER Finger to stop or wait 30 seconds to short + long beep... -
Page 10: Installer Programming Block Diagram
Installer Programming block diagram Swipe the Installer Finger 1 to 4 times depending of the desired menu swipe swipes swipes swipes BACKLIGHT BUZZER RELAY 1 RELAY 2 ON/OFF ON/OFF Time Time Wait Wait Wait Wait 5 seconds 5 seconds 5 seconds 5 seconds (until fast blinking) (until fast blinking) - Page 12 This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with RoHS directive EN50581:2012 Northern Office Videx Security Ltd Unit 4-7 Chillingham ind Est Newcastle Upon Tyne NE6 2XX Tel: 0870 300 1240 Fax: 0191 224 5678...
Need help?
Do you have a question about the B100-SA v2 and is the answer not in the manual?
Questions and answers