Summary of Contents for Perdelle Swan
- Page 1 Perdelle - Swan Assembly Instructions Image 1 Perdelle - Swan Assembly Instructions...
-
Page 2: Table Of Contents
4. PARTS DESIGNATION …………………………………………………………………………………………… 5 5. ASSEMBLY …………………………………………………………………………………………………….……. 6 6. ADJUSTING THE POSITION OF THE PULLEYS …………………………………………………………… 16 7. ADJUSTING THE ELASTIC BANDS' TENSION ………..…………………………………………………… 17 8. USAGE ……………………………………………………………………………………………………………… 19 9. MAINTENANCE - CARE - CLEANING ………..……………………………………………………………… 19 Perdelle - Swan Assembly Instructions... -
Page 3: Important
2. IMPORTANT READ THIS MANUAL COMPLETELY BEFORE ASSEMBLY. The user is responsible for ensuring that Perdelle-Swan is used for its intended purpose. Perdelle-Swan and its accessories are not assembled by a technician, the user bears sole responsibility in the event of breakage, damage, or a device falling due to improper assembly, and Perdelle cannot be held liable. -
Page 4: Packaging - Weight - Dimensions
3. PACKAGING - WEIGHT - DIMENSIONS During delivery, you will receive two packages: 1 carton weighing approximately 4.5 kg 1 pair of bows weighing approximately 2.5 kg 120 cm 110 cm Perdelle - Swan Assembly Instructions... -
Page 5: Parts Designation
4. PARTS DESIGNATION Arches Interface Plastic ring Arm band (x2) Seat bar Handle Plugs (x2) Drum Flange Ring + Pulley butterfly Screw Pair of elastics Pulley barrel Ring button Image 3 Perdelle - Swan Assembly Instructions... -
Page 6: Assembly
• 1 cutting pliers • 1 lighter • 1 meter (measuring tape) • 1 colored marker Image 5: View of the upper part. Image 4: To facilitate assembly, raise the seat to its highest position. Perdelle - Swan Assembly Instructions... - Page 7 … do this … Image 9 : … the body of the cylinder. Image 8 : … spread the ring by hand (or with pliers) to fit it over … Perdelle - Swan Assembly Instructions...
- Page 8 Image 13 : Place the nut covers. interface until it is moderately locked in rotation. Check that the seat can still move up and down. If the seat no longer rises, loosen the bolts slightly. Perdelle - Swan Assembly Instructions...
- Page 9 Image 14 : Assemble the clamping Image 15 : Place the nut covers. bar using the two large bolts. Bolt Image 16 : Screw in the small bolt. Image 17 : Place the nut covers. Perdelle - Swan Assembly Instructions...
- Page 10 Screw in the shown in image 22. The bow should handles without tightening them. rest at the bottom of the hole. Tighten the handle slightly to prevent the bow from rotating freely. Perdelle - Swan Assembly Instructions...
- Page 11 The handles are indexable. Once locked, it is possible to orient them by pulling on them. Perdelle - Swan Assembly Instructions...
- Page 12 28 ... image. Image 29 : … then slide the pulleys Image 30 : Assembly of the barrel and place the two small white caps. button on the elastics. For this … Perdelle - Swan Assembly Instructions...
- Page 13 Image 33 : Ensure that both lengths Image 33 : Pass the elastics through are identical. The assembly is ready to the pulleys, with the barrel buttons be installed. against the pulleys. Perdelle - Swan Assembly Instructions...
- Page 14 Image 36 : Make 2 full loops (do not Image 37 : … secure the elastic in the pass through the lower pin for a third groove of the drum designated for time), and then … this purpose. Perdelle - Swan Assembly Instructions...
- Page 15 Coupe de 80 cm Image 40 : Optionally, cut 80 cm from Image 41: Place the usage label visibly. Perdelle-Swan is ready to be the trailing part of the elastic and burn the end to prevent fraying. Be careful to used.
-
Page 16: Adjusting The Position Of The Pulleys
Image 42 and Image 43 : Position the Image 43 front pulleys above the elbow area (approximately vertical elastics). To do this, use the rotation of the bows and slide the pulleys along the bows. Perdelle - Swan Assembly Instructions... -
Page 17: Adjusting The Elastic Bands' Tension
(Image 46), and test the comfort again. Repeat the process until the user's comfort is achieved. Please note that during adjustment, the user should remove the arm band. Image 46 Perdelle - Swan Assembly Instructions... - Page 18 Test Perdelle-Swan for a few moments. IMPORTANT : When at rest in the arm band, the arms should never be above the working level as shown in Image 47. Use the adjustment to achieve the position shown in Image 48.
-
Page 19: Usage
During use, check that in the high and low seat positions, no component collides with the interface or any part of Perdelle-Swan. - If multiple operators use Perdelle-Swan, it is possible to use one pair of sports bras per user. There are two pairs in the delivered box.