1. Manuals
  2. Brands
  3. Omni3D Manuals
  4. 3D Printers
  5. Omni200
  6. User manual

Omni3D Omni200 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User manual
- 3D printer
Omni200

Advertisement

Table of Contents
loading

Related Manuals for Omni3D Omni200

Summary of Contents for Omni3D Omni200

  • Page 1 User manual - 3D printer Omni200...

  • Page 2: Table Of Contents

    Table of Contents 1. Important Information 1.1. Caution 1.2. Consumables 1.3. Ambient requirements 2. Product Introduction 2.1. Main components 2.2. Extruder 2.3. Build platform 2.4. Accessories list 2.5. Specification 3. Start Up 3.1. Menu preview 3.2. Build platform calibration 3.3. Consumables loading/unloading 3.3.1.

  • Page 3: Important Information

    Use the original power cord to prevent any damage to electrical parts. 1.2. Consumables Omni3D printers can be used with a wide range of filaments. However, for the best print results we recom- mend you to use Omni3D filaments or other good quality materials. Poor quality materials can provide to clogging or even damage the extruder.
  • Page 4 Cautions Uwaga wysoka temperatura Do not touch the heated bed during preheating or printing. Caution high temperature Do not touch the printing head during preheating or printing. Uwaga wysoka temperatura Caution high temperature UWAGA! Trzymaj ręce z dala od ruchomych części Keep hands and other body parts away form moving parts.

  • Page 5: Product Introduction

    2. Product Introduction 2.1. Main components ① Touchscreen ② USB port ③ Build platform ④ Extruder ⑤ Electronics fan ⑥ Power socket and switch...

  • Page 6: Extruder

    2.2. Extruder ① ② ③ ④ ⑤ Nozzle; Heat block; Heater + tempetature sensor; Heatbreak; Heatsink; ⑥ ⑦ ⑧ ⑨ Filament Object fan; Extruder fan; Extruder cover; clamp 2.3. Build platform ① ② ③ ④ Build platform; Magnetic mat; Leveling screw (4 pcs); Heating panel...

  • Page 7: Accessories List

    2.4. Accessories list...
  • Page 8 Name Quantity Power cord USB flash drive Magnetic mat Full metal build platform Extruder ejector rod Wrench 6mm Hex key 1.5 / 2 / 2.5 / 3 mm Spool holder Nozzle cleaning needle Bowden tube Side cutters Feeler gauge Tweezers...

  • Page 9: Specification

    2.5. Specification Operating voltage: 100-240 V/AC, 50/60 Hz Power consumption: max. 320 W Fuse: F10AL, 250 V Print technology: Fused Filament Fabrication (FFF) Build volume (XYZ): 200 x 200 x 200 mm Layer resolution: 0.05-0.3 mm Print speed: 20-100 mm/s Files format: GCODE Nozzle (φ):...

  • Page 10: Start Up

    3. Start Up 3.1. Menu preview - touchscreen is active when the power supply is connected, - touch the screen to perform an operation, - do not touch the screen with the sharp articles. In system menu you can check device information, restore default settings, change menu language and calibrate the touch screen.
  • Page 11 Tools / Manual Manual printer homing, control of movements of each axis and execution of the extruder gear movement. Y axis moves backward Axes homing Platform moves up Retraction X axis moves right X axis moves left Extrusion Platform moves down Back to previous menu Y axis moves forward Movement value setting...
  • Page 12 Tools / Preheating Set the temperature of the build platform and extruder. Press and start heating Current temperature Decrease temperature Target temperature Build platform Increase temperature Hotend Back to previous menu...
  • Page 13 Tools / Filament Consumables loading and unloading. Press and start heating Current temperature Target temperature Stop the movement of the extruder gear Load / Extrusion Unload / Retraction Back to previous menu...
  • Page 14 Tools / Fan Manual fan operation settings. Air volume decrease On / Off Air volume increase Object fan Extruder fan Back to previous menu...
  • Page 15 Tools / Leveling With this tool, you can calibrate the build platform. Detailed instructions can be found in section 3.2. Tools / Stop Printer emergency stop - turn off all the motors and heaters. Printing menu After using this option form the main menu, we go to the selection of the file to print.
  • Page 16 Printing menu Nozzle temperature Stop printing Printing speed Platform temperature mm/s Pause Print time Remaining print time Printing process Printing parameters adjustment...
  • Page 17 Printing parameters adjustment during the process. Print speed percentage Object fan Biuld platform temperature Flow compensation Nozzle temperature Back to previous menu...

  • Page 18: Build Platform Calibration

    3.2. Build platform calibration The build platform has been calibrated and leveled during production, while some deviation may occur during shipping, so leveling must be performed before first print. The leveling procedure is performed automatically. Warning: The platform must be preheated to operating temperature before calibrating. After all the steps, the build platform calibration is done.

  • Page 19: Consumables Loading/Unloading

    3.3. Consumables loading / unloading 3.3.1. Installation of the spool holder and the Bowden tube...

  • Page 20: Consumables Loading

    3.3.2. Consumables loading ① Cut off the end, ensuring a sharp tip and feed it through the bowden. Then insert it into the extruder. ② Enter the “Tools” menu and choose the “Filament” icon. ③ Click on the temperature window to heat the nozzle.

  • Page 21: Consumables Unloading

    ⑤ When the filament melts and comes out smoothly from the nozzle, click the stop icon. 3.3.3. Consumables unloading ① Enter the “Tools” menu and choose the “Filament” icon. ② Press temperature window to start heating. ③ If the set temperature has been reached, press the up arrow and pull the filament out of the extruder.

  • Page 22: Slicing Software Configuration

    3.4. Slicing software configuration Use the installation file included on the USB driver or download the software from the manufacturer’s website https:/ /ultimaker.com/software/ultimaker-cura After installation, run the program and go through the following screens accepting the term of use (Get started > Next > Next > Accept)
  • Page 23 You can create an account, or click Skip to proceed without registering In the next step choose Custom 3D printer from the list and enter the name of the device (e.g. Omni200 / OmniSTART), then click Next...
  • Page 24 Go to Extruder 1 tab and fill in the data as below, according to the data given below then click Next The value of the Z (Heigth) of the printer is for: OmniSTART – 150 mm Omni200 – 200 mm You will be taken to the Cura main menu...
  • Page 25 Loading material settings and printing parameters Click the edit settings button indicated below. After expanding the settings bar, click the Custom button...
  • Page 26 Then select Manage Printers from the Profile drop-down list …...
  • Page 27 In the profile management window click Import, then select the settings file in .curaprofile format from the included USB flash drive or downloaded from the Omni3D website...
  • Page 28 Next go to the Materials tab and click the Import button. Select the .fdm_material files, available on the USB flash drive or downloaded form the Omni3D website, with the settings for the Omni3D filaments. You can also enter weight of the filament and purchase cost...

  • Page 29: D Model Printing

    4. 3D Model printing 4.1. Printing ① Save “.gcode” file on USB drive. ② Insert the USB drive into the printer and select the file to be printed, then confirm. ③ Printing will start automatically, when finished, an audible alarm will sound and the printer will go into "standby"...

  • Page 30: Removing Finished Printout

    4.2. Removing finished printout ① When printing is complete and the platform has cooled down, the magnetic mat can be removed from printer. ② The print can be removed manually without tools.

  • Page 31: Cleaning And Maintenance

    Cleaning and maintanence Never use aggressive detergents, alcohols, or other chemical solutions, because they can damage the surfaces or even impair product performance. Never immerse the device in the water. Danger of burns! Do not touch the hot nozzle directly with bare hands. a) External sufraces - use a dry, soft cloth or brush to clean the outside of the 3D printer b) nozzle...
  • Page 32 c) inside of the extruder Preheat the nozzle to the target temperature, press the filament lever and insert the rod into the extruder, then move up and down several times until the inside of the heatsink and heatbreak are clean. d) magnetic mat Gently scrape the residue with a knife from the surface of the mat.
  • Page 33 ② ④ Remove the defective fuse and replace it with a Reconnect the device new one. to the mains voltage. ③ Carefully push the fuse holder with the new fuse back into the fuse compartment. f) unload filament - see 3.3.3 If you use a filament with admixtures of e.g.

  • Page 34: Materials - Printing Information

    - platform temp.: 40°C ASA-39 CF-PA-12 - using the top cover recommended - Omni200 CF version required - using the top cover recommended - extruder temp.: 230/215°C - it is recommended to coat the magnetic mat - platform temp.: 100°C...

  • Page 35: Troubleshooting

    Problem Possible solution Check the connection to the power supply The 3D printer does not work when turned on. Display and Check the power socket. Is it powered properly? print space remains dark Check the main fuse Remove the USB drive and insert it again Turn the 3D printer off...
  • Page 36 Problem Possible solution Incorrect “.gcode” file data Printing stops during the process Poor connection between USB drive and 3D printer Nozzle or table tempterature is too low, increase it Greasy spots on the platform or other debris making it difficult for material to adhere to the table.
  • Page 37 Problem Possible solution Material blocks during unloading Reload and unload the filament Restart the 3D printer, turn on the head heating (”Preheat” option in the “Tools” menu), wait 2 minutes and check for temperature change The printing head does not heat up or stop heating The temperature sensor or heater is not functioning properly.

  • Page 38: Contact

    Contact Technical support contact Omni3D sp. z o.o. św Michała 43 61-119 Poznań +48 61 666 12 34 +48 886 618 666 service@omni3d.com...

Table of Contents