Advertisement
5.6. Reference(White Balance Adjustment
coordinate and color temperature)
(1) Luminance: 204 Gray, 80IRE
(2) Standard color coordinate and temperature using CS-1000
(over 26 inch)
■ The spec of color temperature and coordinate for Auto W/B.
Mode
Color Temp
Color coordinate
Cool
x = 0.271 (±0.002)
13,000 K
(C50)
y = 0.270 (±0.002)
Medium
x = 0.286 (±0.002)
9,300 K
(0)
y = 0.289 (±0.002)
Warm
x = 0.313 (±0.002)
6,500 K
(W50)
y = 0.329 (±0.002)
* Note : x,y coordinates are drifted about 0.007 after 30 mins
heat-run. So checking color coordinate within 5-min at
total assembly line, consider x,y coordinates might be
up to 0.007 than x,y target of each color temperature.
● W/B Table in process of aging time
- LGD Module
(normal line) March ~ December
Aging time
Cool
color coordinate
x
Target
271
270
1
0-2
282
289
2
3-5
281
287
3
6-9
279
284
4
10-19
277
280
5
20-35
275
277
6
36-49
274
274
7
50-79
273
272
8
80-119
272
271
9
Over 120
271
270
(normal line) January ~ Feburary
Aging time
Cool
color coordinate
x
Target
271
270
1
0-2
286
295
2
3-5
284
290
3
6-9
282
287
4
10-19
279
283
5
20-35
276
278
6
36-49
274
275
7
50-79
273
272
8
80-119
272
271
9
Over 120
271
270
- AUO/ INX/ COST/ SHARP/ BOE Module which cool spec is
13000K
cool
x
y
spec
271
270
target
278
280
Copyright ©
LG Electronics. Inc. All rights reserved.
Only for training and service purposes
Remark
* Test signal
- Inner pattern for
W/B adjust
- External white
pattern (80IRE,
204gray)
Medium
Warm
y
x
y
x
286
289
313
329
297
308
324
348
296
306
323
346
294
303
321
343
292
299
319
339
290
296
317
336
289
293
316
333
288
291
315
331
287
290
314
330
286
289
313
329
Medium
Warm
y
x
y
x
286
289
313
329
301
314
328
354
299
309
326
349
297
306
324
346
294
302
321
342
291
297
318
337
289
294
316
334
288
291
315
331
287
290
314
330
286
289
313
329
med
Warm
x
y
x
Y
286
289
313
329
293
299
320
339
6. Tool Option setting & Inspection per
countries
(1) Press 'IN START' key at Factory Service remote control.
(2) Select 'Tool Option 1'.
(3) Punch in the number and press 'OK'. (Each of models has
their number)
(4) Correct 'Tool Option2' ~ 'Tool Option5'.
(5) Completed adjusting Tool option.
7. Ship-out mode check (In-stop)
▪ After final inspection, press In-Stop key of the Adjustemnt
Remote Control and check that the unit goes to Stand-by mode.
8. AUDIO output check
8.1. Audio input condition
(1) RF input: Mono, 1 KHz sine wave signal, 100% Modulation
(2) CVBS, Component: 1 KHz sine wave signal (0.4 Vrms)
8.2. Specification
y
Item
Min
Audio practical max
Output, L/R (Distortion
4.5
=10% max Output)
9. GND and HI-POT Test
9.1. GND & HI-POT auto-check preparation
(1) Check the POWER CABLE and SIGNAL CABE insertion
condition
9.2. GND & HI-POT auto-check
(1) Pallet moves in the station. (POWER CORD / AV CORD is
tightly inserted)
y
(2) Connect the AV JACK Tester.
(3) Controller (GWS103-4) on.
(4) GND Test (Auto)
- If Test is failed, Buzzer operates.
- If Test is passed, execute next process (Hi-pot test).
(Remove A/V CORD from A/V JACK BOX)
(5) HI-POT test (Auto)
- If Test is failed, Buzzer operates.
- If Test is passed, GOOD Lamp on and move to next
process automatically.
9.3. Checkpoint
(1) Test voltage
- GND: 1.5 KV / min at 100 mA
- SIGNAL: 3 KV / min at 100 mA
(2) TEST time: 1 second
(3) TEST POINT
- GND Test = POWER CORD GND and SIGNAL CABLE
GND.
- Hi-pot Test = POWER CORD GND and LIVE &
NEUTRAL.
(4) LEAKAGE CURRENT: At 0.5 mArms
- 11 -
Typ
Max
Unit
Remark
(1) Measurement condition
W
5.0
6.0
- EQ/AVL/Clear Voice: Off
Vrms
(2) Speaker (8 Ω Impedance)
LGE Internal Use Only
Advertisement
