CEJN 913 Series Manual

Open hose reels
Series 913 Guide
Want to learn more about the open hose reels go to
i
www.cejn.com/product-categories/hose-cable-reels/
1. Safety
IMPORTANT!
- The products are intended for use by knowledgeable persons having the technical skill necessary to evaluate their suitability for specific
applications.
- Read all safety instructions carefully before attempting to install, operate or maintain this product.
- Do not leave the hose to coil unattended.
- Only qualified personnel should undertake the installation, commissioning, and maintenance of this product.
- Before carrying out maintenance or repair work, always disconnect the hose reels from the media.
- If the reel must be disassembled, release spring tension before further dismantling.
- Close the feed of fluids at the end of the workday to prevent damages during non-working hours.
- Ensure that the pressure does not exceed the maximum working pressure of the lowest rated system component.
- CEJN AB does not take responsibility for damage that occurs if the reel had been modified or used in a way that was not intended.
Nor for damages due to incorrect installation or maintenance.
WARNING! Keep away from moving parts!
2. Intended use of the machine
The hose reels in the powder coated series are suitable for compressed air or different kinds of fluids at low and high temperature.
The hose reels in stainless and acid proof steel are suitable for wash down and cleaning applications at high and low temperature. Some
versions are fitted with hose suitable for food and beverage industry. Please consider industry-specific regulations regarding cleaning and
service instructions for the intended application.
For information regarding different model's specifications see list at: www.cejn.com/product-categories/hose-cable-reels/
3. Installation
Mount the hose reel on stiff and consistent walls, using 4 screws M10. If the hose reel is wall mounted, note that it must be
mounted at a minimum of 2,5m from the floor to prevent accidents and injuries during operation.
For more detailed information: www.cejn.com/guides-support/movies
3.1 Assembly
1
N
D
Arm-positions
4
E
3.3 Mounting of the hose
(Models without hose)
The hose reels without hose are supplied with
the unloaded spring. Use a hose with dimension
and pressure characteristics suitable for use
according to the hose reel model.
3.3.1 Fix the hose reel to the bench. Put the hose between the guide rollers, connect it
to the fitting which is inside the drum and tighten by the suitable wrench.
3.3.2 Manually rotate the drum in order to completely rewind the hose.
3.3.3 To preload the spring hold the hose-end and manually rotate the drum in the
opposite direction for a few turns, according to table 13 (last page). Insert the
hose-end between the guide rollers again.
2
i
3.2 Swing bracket
C
Swing brackets are available as an accessory,
standard reel are fixed 90 degrees from the
wall and the swing bracket
B
allow the reel to swing
+-50 degrees.
A
6
D
3.3.1
C
B
A
A3
6
GB
6 5
D
6 5
C
D
C
305
380
260
12(4x)

C
B
B
160
230
243
200
C-C
12(4x)

B
A 150
Product Data - Stainless Steel Reels (Wash Down)
6 Art.no. 5 Hose length 4 IDxOD [mm]
19 913 1220 20m (65ft) 19x27
A3
B-B
D 6 5
Product Data - Stainless Steel Reels (Wash Down)
A
C
6
Art.no. Hose length IDxOD [mm]
D
19 913 1120 20m (65ft) 13x20
A3
6 5
B
C
A
A3
6 5 4
B
5 4 6 3 5 2
A
D
A3
6
3.3.2
C
B
3.3.4 Put the hose rubber stopper at the desired length.
3.3.5 Unwind the hose and rewind it completely, to check if the hose reel works
A
Scale properly. Drawn Checked Appr.
1 : 5 CABLIJA
Drawing No.
Assembly Drawing
A3
5 4 6 3 5 2
DO NOT PUT HANDS OR ANY OTHER THING INSIDE THE DRUM!
4 3
Swivel conn. (4)
 442 (17,5")
Swivel conn. (3)
4 3
Conn. 2
Swivel conn. (4)
C  442 (17,5")
Swivel conn. (3)
193
470
Mounting-positions
Conn. 2
3
B
A
Technical Data:
200
Hose material: PVC
469,9
Max Temperature: 70°C
Sealing material: Viton
Max pressure: 10bar(140PSI) 70°C / 20bar(280PSI) 25°C
Feeder hose included in box (not mounted)
Reel material: AISI 304 (Swivel nut in brass)
Feeder hose length: 1m
Hose Reel Swivel connections:
C
INLET: R 1" female (3)
OUTLET: R 3/4" male (4)
Technical Data:
Scale
3 Conn.1 2 Conn. 2 1 Weight [kg]
1 : 5
Hose material: PVC
R 3/4"" (fem)
Assembly Drawing
R 3/4" (male) 30
Max water temperature: 70°C
Swivel nut
Sealing material: Viton
4 D 3
Max pressure: 10bar(140PSI) 70°C / 20bar(280PSI) 25°C
Reel material: AISI 304 (Swivel nut in brass)
Feeder hose length: 1m
Hose Reel Swivel connections:
INLET: R 1/2" male (3)
OUTLET: R 1/2" male (4)
C
5 4 3 2 1
Conn.1 Conn. 2 Weight [kg]
Scale Drawn
1 : 5 CABJOOL CABANLA
R 1/2" (fem)
Assembly Drawing
R 1/2" (male) 25
Swivel nut
4 3
B
A
Scale Drawn Checked Appr. ECO Date
1 : 2,5 CABJOOL JOTU JOOL 2021-03-12
Drawing No. Issue Sheet
Assembly Drawing 1 /(1 )
AA
3 2 1
4 1 3 2 1
D D
Scale 1 : 2,5 CABJOOL Drawn Checked JOTU Appr. JOOL ECO Date 2021-03-12
Drawing No. Issue Sheet
Assembly Drawing
AA 1 /(1 )
5 4
3 2 1
3.3.3 3.3.4
C C
B B
A A
ECO Date Scale Drawn Checked Appr. ECO Date
1 : 5 CABLIJA
Issue Sheet Drawing No. Issue Sheet
Assembly Drawing
AA 1 /(1 ) AA 1 /(1 )
4 1 3 2 1
Edition A - 2023-08-15
CEJN AB
Rattvägen 1
SE-541 25 Skövde
Sweden
www.cejn.com
2 1
D
2 1
1 : 7
D
C
Conn. 1
1 : 7
C
B
Conn. 1
B
B
A
Drawn Checked Appr. ECO Date
CABJOOL CABANLA CABOG 000818 2021-01-26
Drawing No. Issue Sheet
509131220
AA 1 /(1 )
2 1
A
Checked Appr. ECO Date
CABOG 000818 2021-03-03
Drawing No. Issue Sheet
D
509131120
AA 1 /(1 )
2 1
C
B
A