Related Manuals for Ningbo EF449B
Summary of Contents for Ningbo EF449B
- Page 1 MODEL: EF449B/EF450B/EF451B/EF452B/EF453B Email: service8@fireandfireplaceservice.com...
- Page 3 This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least a 3 feet (a 0.9m) from the front of the heater and keep them away from the sides and rear.
- Page 4 A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
- Page 6 MODEL NO.: EF449B/EF450B/EF451B/EF452B/EF453B Supply Voltage: AC120V/60Hz Maximum power consumption: 1.5KW Power for flame and fuel bed effect: 5.8W/5.8W/7.2W/8.7W/10.1W 8/8/8/10/10x Firebox Screw ST4*10 Screw ST4*40 Screw ST5*40 8/8/8/10/10x Standing Bracket Crystal Media Wall Plug Bracket Battery Remote Control Instruction Manual...
- Page 7 Email: service8@fireandfireplaceservice.com 5 ⁄ " 5 ⁄ "...
- Page 8 A screwdriver and a Φ8mm impact drill will be needed. WARNING! Risk of Fire! Keep electric cords, drapery, furnishings or other combustibles at least 3ft. (0.9m) from the front of the electric fireplace.
- Page 9 Installing the Appliance REMOVE WALL MOUNTING BRACKET REMOVE THE FRONT GLASS PANEL Remove the screws for fixing the front glass panel from two sides of the appliance, and then , carefully lift upward the front glass panel to take it down. Lock hook...
- Page 10 NOTE: Save all the parts removed from the appliance. CHOOSE A WAY TO INSTALL IN WALL RECESSED Build a frame with power supply as shown below. Min.5 ⁄ " MODEL EF449B EF450B EF451B EF452B EF453B 32 ⁄ " 36 ⁄ "...
- Page 11 Remove the log fuel bed if you want to replace it with crystal media. HOW TO REMOVE LOG FUEL BED Remove and save the galvanized screws on both sides for fixing the fuel bed to take down it. Insert the firebox into the framework and fix it by four ST4x40 screws. Evenly scatter the crystal media on the fuel bed.
-
Page 12: Wall Mounted
Install the front glass panel back .Make sure the hook is fully hooked into the lock. The installation is completed now. Lock hook WALL MOUNTED Place the wall mounted bracket in the desired position ensuring that the bracket is leveled. Mark and drill the holes. Ceiling Wall Floor... - Page 13 Fix the L brackets to the bottom of the firebox with four ST4*10 screws. Hang the firebox on the wall bracket and mark the position of the L bracket ,then take the firebox down. Drill 2 holes on the marked point, insert 2 wall plugs into the holes, then hang on the firebox again and fix it by two ST5*40 screws.
- Page 14 Repeat the steps mentioned above to arrange the fuel bed and install the front glass panel and fix it to the sides of firebox with the screws. FREE STANDING Install the standing bracket on the bottom of the appliance with four ST4*10 screws.
-
Page 15: Before Operation
OPERATING INSTRUCTION BEFORE OPERATION WARNING! Do not operate the appliance if it is damaged or has malfunctioned. If you suspect the appliance is damaged or has malfunctioned, call a qualified service engineer to inspect the appliance, and replace any part of the electrical system if necessary, before re-use. WARNING! To reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 meter from the air outlet. -
Page 16: Manual Control
MANUAL CONTROL HEATING INDICATOR DISPLAY FLAME HEATER STAND BY TEMPERATURE 7 DAYS TIMER INDICATOR 1. STAND BY:Turns on the appliance with the last used settings including heater. Place the appliance into standby mode with all features turned off. 2. FLAME: Press to cycle through 9 flame colours and off setting. 3. -
Page 17: Remote Control
REMOTE CONTROL NOTE: Ensure that the ba eries of remote handset are new and inserted • correctly. Aim the remote control at the remote receiver which is behind the • right side of the flame screen. STAND BY FLAME BRIGHTNESS TEMPERATURE HEATER 7 DAYS TIMER... - Page 18 Cycle through 5 settings of L5, L4,L3,L2,L1,L0. brightness of flame and fuel BRIGHTNESS bed. Cycle through low heater, Lo=low heat setting high heater and off setting. HI=high heat setting The heater indicator will turn off after 10 seconds if the flame effect is on 16,17,18,19,20,21,22,23, Adjust the heaters response 24,25,26,27,28,58...
- Page 19 SET UP CURRENT DAY AND TIME Hold time button on the remote to enter date and time setting mode; Repeatedly press time button to select date, D1-D7 will show on the display which represents Monday-Sunday. Press button to confirm, and then automatically enter hour setting.
- Page 20 1. Two AAA alkaline batteries are required for the remote control; 2. Two Use the thumb press and push the bar figure on the back cover down simultaneously, then take out the cover and remove the battery or insert the battery, after this place the cover back on the rear of the remote;...
- Page 23 Fuel Bed LED Board Receiver...
- Page 24 Ningbo Richen Electrical Appliance Co., Ltd. Address: No. 19, Yongdinghe Road, Xiapu, Beilun, Ningbo, Zhejiang, P.R.China 3.EF.449.05.106 A1...