Related Manuals for Ningbo DBL2000-BX
Summary of Contents for Ningbo DBL2000-BX
- Page 1 Electric fireplace DBL2000-BX Operation Manual To keep from dangerous, please read the manual carefully before you use or maintain the fireplace。...
- Page 2 Ningbo Globaltec Science & Technology Co., Ltd Thank you for your choosing our DBL-2000 decorative electric fireplace. New LED flame system, avoiding the need to change bulbs.Before use it, please read the manual carefully, and take it for future use.
- Page 3 Safety Information 1. Please read all instructions before using the fireplace； 2.This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. You should keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from front of heater and keep them away from sides and rear.
- Page 4 9. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or the like. Arrange cord away from traffic area and where it will not be tripped over. 10. To disconnect electric fireplace, turn controls to "OFF" before removing plug from outlet.
- Page 5 20. To prevent a possible fire, do not burn wood or other materials in this electric fireplace. 21. To prevent electric shock or fire, always hire a certified electrician should new circuits or outlets be required. 22. When transporting or storing this electric fireplace, keep in a dry place free from excessive vibration and store as to avoid damage.
- Page 6 Technical data Rated power： 1500W Rated Voltage：120VAC Frequency： Installation Attentions 1) You should keep combustible materials, such as: curtains, furniture, pillows, clothes, bedding, paper, etc., at least 1M from the front of the unit. 2) Do not use this unit in areas where gasoline, paint or other flammable liquids or their associated vapors may be present.
- Page 7 Installation method (See Figure 1) Figure 1 Specifications (see Figure 2) Figure 2...
- Page 8 Function Description Figure 3 1. Power Switch 2.embers Adjuster 3. Flame Adjuster 4．Remote/Manual Shift Switch 5.Temperature Adjuster Once the unit has been properly connected to a ground electrical outlet, it is ready to operate. 1. Turn the Power Switch to position “I”，you will hear two tweets buzzer，the fireplace is connected to power supply and ready for operating;...
- Page 9 Remote button see Figure 4： Figure 4 The functions identified on the remote(see Figure 4) are fellows: A.POWER BUTTON Press once to turn on power to fireplace B. INDICATING LIGHT Illuminates when signal is sent C. EMBERS BUTTON On/off switch for flame and ember light D.
- Page 10 G.TEMPERATURE ADJUSTMENT BUTTON(HIGH) Highest heat output,up to 28℃. H. TEMPERATURE ADJUSTMENT BUTTON(MED) Medium heat output,up to 22℃. I. TEMPERATURE ADJUSTMENT BUTTON(LOW) Lowest heat output,up to 16℃. J.FLAME ADJUSTING BUTTON(LOWER) Reduces flame intensity. K.FLAME ADJUSTING BUTTON(HIGHER) Increases flame intensity. Remote Control Operation Steps: 1.When operating the remote control,it must be pointed at the logs inside the electric fireplace and a beep must be heared each time you press a function button,The beep lets you know the remote control is operating the function...
- Page 11 beep,and the brightness will decrease slightly until the minimum brightness is achived. 4.Heater Button-To activate the heater,press the heater button (see F),then press HI(G).MED(H),or LO(I).The heater is preset to the following temperatures: .HIGH will shut off when room reaches approximately 28℃ .MED will shut off when room reaches approximately 22℃...
- Page 12 Maintenance Attention: 1．Always disconnect the heater from the electrical supply before carrying out cleaning, maintenance 2．Use with a damaged power cord. Get it replaced by a qualified technician. TROBULESHOOTING GUIDE 1、Can not turn on the electric fireplace Cause: please check the power switch and make sure there is electricity in the power outlet.