Table of Contents
Advertisement
Quick Links
What's Inside the Package
• 80 LED matrix light w/motion detector
• Solar charger board
• User Manual
Note：Packaging items
LED
1X
SENSOR LIGHT
Note：Please according to demand a purchase.
Introduction
Thank you for purchasing SOLAR POWERED WITH MOTION ACTIVATED 80 LED
SECURITY FLOOD LIGHT
With its effortless setup and lightweight design, the light conforms to all your lighting needs. It was made to provide
many years of service using environmentally friendly solar power.
SPECIFICATIONS
• Coverage: 180º sensing angle
• Detection range:15M ( 25ºC)
• LED single power: 0.06W
• Matrix light: 80 super bright LEDs
• Rated load: 4.7W Max.
• Light-control:<10LUX
• Battery: 7.4V 2000mAH lithium battery
Solar Power Sensor Lamp
Solar panels
1X
10V/2.5W
Φ6 Expand screw
Cord: 5M
Car-mounted Charger
12V Convert 9V
Tel: 86-574-83008608(20 lines)
PD-SLL80 instruction
8X
4x30 Screw
Auto repair lighting
Outdoor camping lighting
• Solar charger board: 10VDC/2.5W Monocrystalline
(with 15' cable) ( Life: over 3 years )
• Continuous illumination time: ≥4 hours
• Time delay: Min. 10 seconds, Max. 3 min.
• LED light installation height: 1-3m
• Operation temp.: -10 ºC to +40 ºc
• luminous flux: 210lm
178mm
100mm
177mm
8X
Charger
100V-240V Convert 9V
94mm
50mm
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Lexing PD-SLL80
Summary of Contents for Lexing PD-SLL80
- Page 1 Solar Power Sensor Lamp PD-SLL80 instruction 178mm What’s Inside the Package 100mm 94mm 177mm • 80 LED matrix light w/motion detector • Solar charger board • User Manual 50mm Note：Packaging items Solar panels 10V/2.5W SENSOR LIGHT Φ6 Expand screw 4x30 Screw Cord: 5M Note：Please according to demand a purchase.
- Page 2 Solar Power Sensor Lamp PD-SLL80 instruction Important Safety Information • Do not dispose of battery in fire. This may result in an explosion. • Do not expose the light to fire or intense heat as the battery may explode. • Do not immerse in water.
- Page 3 Solar Power Sensor Lamp PD-SLL80 instruction SENSOR INFORMATION 180° Correct moving orientation Detection angle SPECTROGRAM Quick Setup Procedure 1. Please keep it away from the children. Warning! 2.This product can installed for outdoor, but we suggest that against for the rain/storm & High lights.
- Page 4 Solar Power Sensor Lamp PD-SLL80 instruction 1. Mark the wall where you wish to mount the light. 2. Drill all four holes. Place the mount on the wall with nylon anchors ( if needed) and screws. 60mm 66mm 3. Please connect the battery according to diagram in the warning part of the instruction book, and assemble the battery cover as it was.
- Page 5 Solar Power Sensor Lamp PD-SLL80 instruction 7. Adjust the motion detector direction. It can be set at the range of 8second (counterclockwise rotation to the end) to 3minute(clockwise rotation to the end) .The timer will recount when the sensor detect a moving signal before the end of the last time, so we advise that you’d better set the time...
- Page 6 Solar Power Sensor Lamp PD-SLL80 instruction 3. “OFF” Statues The system will be in “power fail safeguard” model. No motion detecting function. Consumes ＜25UA. 4. “AUTO” Statues The system will accept the manual adjustment for “Delay Time” and “Sensi Tivity”.
- Page 7 Solar Power Sensor Lamp PD-SLL80 instruction 3.The LEDS in serial can function when all the seals installed in place. 4.Please don’t remove or connect with other lamp when powered on. 5.When the LEDS in serial are damaged ,you need experienced technician to repair using the same rating LEDS.
Need help?
Do you have a question about the PD-SLL80 and is the answer not in the manual?
Questions and answers