Table of Contents
Advertisement
Quick Links
LX-SLL80 Solar Power Sensor Lamp Instruction
What's Inside the Package
• 80 LED matrix light w/motion detector
• Solar charger board
• User Manual
Note:Packaging items
LED
1X
SENSOR LIGHT
Note:Please purchase according to demand.
Introduction
Thank you for purchasing SOLAR POWERED WITH MOTION ACTIVATED 80 LED SECURITY
FLOOD LIGHT
With its effortless setup and lightweight design, the light conforms to all your lighting needs. It was made to provide
many years of service using environmentally friendly solar power.
Specifications
• Coverage: 180º sensing angle
• Detection range: 15m ( 22ºC) (adjustable)
• LED single power: 0.06W
• Matrix light: 80 super bright LEDs
• Rated load: 4.7W Max.
• Light-control: <10LUX
• Battery: 7.4V, 2600mAH lithium battery
Solar panels
1X
10V/2.5W
Φ6 Plastic expansion
Cord: 5M
Car-mounted Charger
12V Convert 9V
8X
4x30 Screw
Auto repair lighting
Outdoor camping lighting
• Solar charger board: 10VDC/2.5W Monocrystalline
(with 15' cable) ( Life: over 3 years )
• Continuous illumination time: ≥ 4 hours
• Time setting: Min. 10 seconds, Max. 3 minutes. (adjustable)
• LED light installation height: 1m to 3m.
• Working temperature: -10 ºC to +40 ºC
• Luminous flux: 210lm
178mm
100mm
177mm
8X
Charger
100V-240V Convert 9V
94mm
50mm
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Lexing LX-SLL80
Summary of Contents for Lexing LX-SLL80
- Page 1 LX-SLL80 Solar Power Sensor Lamp Instruction 178mm What’s Inside the Package 94mm 100mm 177mm • 80 LED matrix light w/motion detector • Solar charger board • User Manual Note:Packaging items 50mm Solar panels 10V/2.5W SENSOR LIGHT Φ6 Plastic expansion 4x30 Screw Cord: 5M Note:Please purchase according to demand.
- Page 2 Important Safety Information • Do not dispose of battery in fire. This may result in an explosion. • Do not expose the light to fire or intense heat as the battery may explode. • Do not immerse in water. • Never look directly into the light or shine it into another person’s eyes. •...
- Page 3 Sensor Information 180° Correct moving orientation Detection angle Spectrogram Quick Setup Procedure 1. Please keep it away from the children. Warning! 2.This product can installed for outdoor, but we suggest that against for the rain/storm & High lights. Note:Please bring the following tools Pencil Electric drill Hammer...
- Page 4 1. Mark the wall where you wish to mount the light. 2. Drill all four holes. Place the mount on the wall with nylon anchors ( if needed) and screws. 60.00 66.00 3. Please connect the battery according to diagram in the warning part of the instruction book, and assemble the battery cover as it was.
- Page 5 7. Adjust the motion detector direction. It can be set at the range of 8second (counterclockwise rotation to the end) to 3minute(clockwise rotation to the end) .The timer will recount when the sensor detect a moving signal before the end of the last time, so we advise that you’d better set the time to minimum when you make the detection range testing or the walking testing.
- Page 6 When the external ambient light values > 200LUX, the system will shut off PIR sensor; Power consume: ＜3 MA Electrical current:570~660 MA (when all the lights are fully on) When the power is lower than <6.4V, the system turn OFF. When the battery is lower than 6.6V, the LED indication light will be blinking every 30secs for a period of 8 hours ,after 8 hours ,the voltage is not complete to sustain the work.
- Page 7 3.The LEDS in serial can function when all the seals installed in place. 4.Please don’t remove or connect with other lamp when powered on. 5.When the LEDS in serial are damaged ,you need experienced technician to repair using the same rating LEDS. ●...
Need help?
Do you have a question about the LX-SLL80 and is the answer not in the manual?
Questions and answers