Related Manuals for NEU MASTER NTC0070-4
Summary of Contents for NEU MASTER NTC0070-4
- Page 1 NTC0070-4 Cordless Staple Cordless Tacker SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. REV:2.0...
- Page 2 1) to avoid injury and misuse, please read the manual before operation. 2) follow all safety information that follows this mark to avoid possible injury or death. 3) in order to avoid hearing damage, it is necessary to wear ear protection device when operating tools to avoid completely dangerous hearing.
- Page 3 ASSEMBLY 1. Make sure you have read all safety instructions. 2. This tool comes completely assembled. There is no assembly required. LOADING STAPLES 1. Make sure tool is powered off. 2. The TC0070-4 has a bottom load staple magazine. Turn tool upside down and squeeze pusher assem- bly(Fig 1).
- Page 4 FIRING YOUR TOOL I. To fire your tool, place down on your work piece depressing the contact safety on the front of the tool. Once the contact safety, is depressed, push the trigger to fire your staple. You must pick up the front of the tool and reactivate the contact safety for each shot.
- Page 5 3. DO NOT charge the tool battery in an air temperature below +40°F(+4℃), or above +105°F(+40°C). This will prevent serious damage to the battery. 4. It is recommended to wait 15 minutes after charging before using the tool to avoid the possibility of the tool overheating and damaging the battery.
- Page 6 WARINING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term ”power tool” in the warnings refers to your (cordless)power tool. 1.WORK AREA SAFETY a) Keep work area clean and well lit.
- Page 7 c) Ensure power switch is in off position and disconnected from the charger power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children, and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
- Page 8 Additional security warnings Power tool fasteners. Careless use of tools can cause accidental fire and personal injury to fasteners. Don't point the tool at yourself or anyone nearby. Accidental triggering can cause firmware to fall off and may cause damage. Do not start the tool unless it is firmly against the work piece.
Need help?
Do you have a question about the NTC0070-4 and is the answer not in the manual?
Questions and answers
I need the charging system for NTC0070-4 cordless tacker
The NEU MASTER NTC0070-4 cordless tacker has a built-in lithium-ion battery and uses a USB charging system. It comes with a 1-amp charger, which can also be used with a computer USB port. Charging time is up to 1.5 hours. The charging indicator shows red while charging and green when fully charged. It is recommended to wait 15 minutes after charging before using the tool to prevent overheating. The battery should not be charged in temperatures below 40°F (4°C) or above 105°F (40°C).
This answer is automatically generated
How can I obtain the charging system for the NTC0070-4 cordless tacker
You can obtain a charging system for the NEU MASTER NTC0070-4 cordless tacker by purchasing a compatible Micro USB 5V charging cable and power cord. This charger is available on online retail platforms such as Amazon. Ensure you use the correct charger provided for safe and efficient charging.
This answer is automatically generated
How can I obtain the charging system for the NTC0070-4 cordless tracker
My stapler wouldn't fire a staple so my husband opened it up to look at it. A spring popped out, can someone please tell me where that spring goes to put it back together correctly?
The spring in the NEU MASTER stapler model NTC0070-4 is part of the pusher assembly. It is located inside the bottom-load staple magazine and helps push the staples forward. The pusher assembly should be pulled out until it stops to load staples and then closed until it snaps into place. Never remove the pusher assembly completely, as this may damage the tool.
This answer is automatically generated