Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for NEU MASTER NTC0023-18
Summary of Contents for NEU MASTER NTC0023-18
- Page 1 NTC0023-18 Cordless Tacker SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
- Page 2 Please read all instructions carefully before use and retain for future reference. CAUTION Do not immerse in water. Wear a dust mask Protect your eyes. Protect your ears. Protect your hands. WARNING! Some dust created by construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
- Page 3 1. Contact safety 9. Battery Release Button 2. LED Light 10. Battery Power Display Button 3. Impact Control Adjustment Knob 11. Battery Indicator LEDs 4. Trigger 12. Charger Pins 5. Handle 13. Light(Red) 6. Magazine Release Clip 14. Light (Green) 7.
- Page 4 STAPLE NAIL gauge crown L=15, 20, 25, 30, 32 mm L=15-25 mm CHARGING Charging: Red light, ashing green light Hot/Cold delay: Flashing red light Gharger: Long green light Problem pack or Charger: Both red and green lights are ashing BATTERY...
- Page 5 Battery pack installation and removal STAPLE...
- Page 6 NAIL...
-
Page 7: Operation
OPERATION... - Page 8 OPERATION...
-
Page 9: Clearing A Jam
CLEARING A JAM... - Page 10 INTENDED USE Only operate the power tool/machine for its WORK AREA SAFETY Keep work area clean and well lit. Cluttered or dark areas invite accidents. manual. Do not operate power tool/machine in explosive atmospheres, This power tool/machine is for domestic use only. Do not use outdoors or on wet surfaces.
- Page 11 If the power cord is damaged, it must be replaced by a quali Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited Keep the ventilation slots and motor housing as free of dirt by conductive materials.
-
Page 12: Technical Specification
Do not use an extension cord unless absolutely necessary. electric shock. Never attempt to connect two chargers together. Use the battery charger indoors only. Make sure that the charger cable is positioned where it will not be stepped on, tripped over or otherwise subjected to damage or stress.
Need help?
Do you have a question about the NTC0023-18 and is the answer not in the manual?
Questions and answers
First time use of product. Was working OK then fires 1 nail then stops. The product is the neu master 0023-18 cordless tacker.
The NEU MASTER NTC0023-18 cordless tacker may fire one nail and then stop working due to several possible reasons:
1. Battery Issue: The battery may be low or not properly connected. Check the battery power display and ensure it is fully charged and securely attached.
2. Contact Safety Not Engaged: The contact safety must be pressed against the surface for the tacker to operate. If not properly engaged, it will not fire.
3. Jammed Nail or Staple: A jammed fastener in the magazine or nose area can cause it to stop. Check and clear any jams.
4. Magazine Issue: If the magazine is empty or not properly loaded, it may prevent further shots. Ensure it is correctly filled and latched.
5. Overheating or Safety Lock: The tool may have a safety mechanism that stops firing if overheated or misused. Allow it to cool and reset.
Check these points to identify the cause.
This answer is automatically generated
Neu Master nail gun will not feed nails. loaded correctly but when I pull trigger it only leaves a dent in the wood. No nail
The NEU MASTER NTC0023-18 nail gun may not be feeding nails and only leaving dents in the wood due to the following possible reasons:
1. Empty or Improperly Loaded Magazine – Ensure that nails are properly loaded in the magazine and that it is not empty.
2. Incorrect Nail Size – The nail gun supports 18-gauge brad nails from 5/8" to 1 1/4". Using incorrect nail sizes may cause feeding issues.
3. Low Battery Power – If the battery is low, the tool may not have enough power to drive the nails properly. Check the battery indicator LEDs and recharge if necessary.
4. Impact Control Adjustment – The impact control adjustment knob may be set too low, preventing the nail from being fully driven into the wood. Increase the setting as needed.
5. Jammed Nails – A nail jam inside the magazine can prevent new nails from feeding. Open the magazine, check for obstructions, and clear any jams.
6. Rust or Dirt in the Nail Compartment – If nails have been left inside the tool for a long time, especially in cold weather, rust buildup may cause feeding problems. Clean the nail cartridge compartment if necessary.
Checking and addressing these issues should resolve the problem.
This answer is automatically generated