Table of Contents
Related Manuals for Wenglor I08G003
Summary of Contents for Wenglor I08G003
- Page 1 Inductive Sensors with Full-Metal Housing Operating Instructions Translation of the original operating instructions Subject to change without notice Available as PDF file only Version 1.0.0 Status: 26.10.2023 www.wenglor.com...
-
Page 2: Table Of Contents
Table of Contents General ................................4 Information Concerning these Instructions ..................4 Explanations of Symbols ........................4 Limitation of Liability ..........................5 Copyrights ............................5 For Your Safety ............................6 Use for Intended Purpose ........................6 Use for Other than the Intended Purpose ....................7 Personnel Qualifications ........................7 Modification of Products ........................7 Safety Precautions ..........................7 2.5.1 General Safety Precautions .....................7... -
Page 3: General
• Local accident prevention regulations and national work safety regulations must be complied with as well. • The product is subject to further technical development, and thus the information contained in these oper- ating instructions may also be subject to change. The current version can be found at www.wenglor.com in the product’s separate download area. -
Page 4: Limitation Of Liability
• wenglor assumes no liability for printing errors or other inaccuracies contained in these operating instruc- tions unless wenglor was verifiably aware of such errors at the point in time at which the operating instruc- tions were prepared. -
Page 5: For Your Safety
For Your Safety 2.1 Use for Intended Purpose This wenglor product is intended for use in accordance with the following functional principle Inductive Sensor with Full-Metal Housing Inductive sensors with full-metal housing made of stainless steel 316L (1.4404/316L) are impact-resistant, resistant to chemicals and high water pressure (IP68/IP69K). -
Page 6: Use For Other Than The Intended Purpose
• No safety components in accordance with 2006/42/EC (Machinery Directive). • The product may be used only with accessories supplied or approved by wenglor, or in combination with approved products. A list of approved accessories and combination products can be found at www.wenglor.com on the product detail page. -
Page 7: Technical Data
Technical Data The specific technical data for the respective product can be found on the product detail page at www.wenglor.com. 3.1 Scope of Delivery • Sensor • Packaging bag incl. quick start printing • Nut set (with I08, I12, I18, I30) Transport and Storage 4.1 Transport... -
Page 8: Installation And Electrical Connection
• The sensing face of the sensor may not contact any other machine parts. • Installation instructions must be observed (see product detail page at www.wenglor.com) • Specified torque values must be complied with (see product detail page at www.wenglor.com) ATTENTION! Risk of property damage in case of improper installation! The product may be damaged. -
Page 9: Installation Instructions
5.2 Installation Instructions 5.2.1 Installation Instructions in Accordance with Standard bau für induktive Sensoren: änden der Bauform IJ 8×Sn Installation dimension Description Minimum distance from sensor to damping material (e.g. steel). Minimum distance between two inductive sensors. This clearance applies to installation in air. If the sensors are installed within an attenuating material (e.g. -
Page 10: Installation Instructions For Sensors With Weprotec
5.2.2 Installation instructions for sensors with weproTec weproTec is the abbreviation for wenglor proximity switch technology, an innovative, patented wenglor tech- nology for inductive sensors. Inductive sensors with weproTec can be mounted very close to each other ( installation dimension B1) or opposite one another (1.5 ×Sn). - Page 11 Installation variant Description Two sensors can be mounted next to each other in area B1. Permissible! Two sensors can be mounted next to each other from installation Permissible! dimension B. Two sensors must not be mounted next to each other in front of area Impermissible! Two sensors must not be mounted in the area between B1 and B.
-
Page 12: Switching Distance
5.3 Switching distance • The switching distance described in the data sheet is the nominal switching distance Sn according to the standard. • The switching distance refers to a standard measuring plate (material: steel, thickness: 1 mm, side lengths: 3× Sn or outside diameter sensor). •... -
Page 13: Electrical Connection
• Shut down the machine. • Analyze and eliminate the cause of error with the aid of the diagnostics information. • If the error cannot be eliminated, please contact wenglor’s support department • Do not operate in case of indeterminate malfunctioning. -
Page 14: Maintenance Instructions
Working distance 8.2 Index of Changes Version Date Description/Changes 1.0.0 26.10.2023 Initial version of the operating instructions 8.3 Declarations of Conformity The declarations of conformity can be found on our website at www.wenglor.com in the product’s separate download area. Maintenance Instructions... - Page 15 Inductive Sensors...
Need help?
Do you have a question about the I08G003 and is the answer not in the manual?
Questions and answers