Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Echo 06001247
Summary of Contents for Echo 06001247
- Page 1 SHRED 'N' VAC Operator's Manual MODEL ES-231 Serial Number 06001001 - 06001247 WARNING DANGER Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual which must be read and understood for proper and safe operation. X753000370 X7531130700 03/03...
-
Page 2: Table Of Contents
NTRODUCTION Welcome to the ECHO family. This ECHO product was designed and manufactured to provide long life and on-the-job- dependability. Read and understand this manual. You will find it easy to use and full of helpful operating tips and SAFETY messages. -
Page 3: Manual Safety Symbols And Important Information
If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING instructions for specific information. P/N 89016006361... -
Page 4: International Symbols
Heavy protective clothing can increase operator fatigue Wear a face mask to protect against dust. which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures Hearing Protection are cooler. ECHO recommends wearing hearing protection whenever unit is used. -
Page 5: Extended Operation/Extreme Conditions
NOT operate unit if leaks are found. • Do not use blower if any part is missing or damaged. • Have repairs done only by an authorized ECHO Service dealer. • Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual. -
Page 6: Safe Operation
SAFE OPERATION Noise Control • Follow local noise regulations on sound WARNING DANGER levels and hours of operations. Use only during appropriate hours. Do not operate this product indoors or in inadequately ventilated • Never use a higher speed setting then areas. -
Page 7: Description
1 - Elbow Pipe 1 - Debris Bag 1 - Operator's Manual 1 - Warranty Registration Card 1 - ECHO Emissions and Warranty Statement 1 - T-Wrench 1- Echo Power Blend 2-stroke oil sample 1. STOP SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start and run. Slide back to stop. -
Page 8: Specifications
PECIFICATIONS ® MODEL ----------------------------------------------------- ES-231 SHRED 'N' VAC Length ------------------------------------------------------- 335 mm (13.2 in.) (w/o blower pipes) Width (w/rear handle) ------------------------------------- 305 mm (12.0 in.) Height ------------------------------------------------------- 375 mm (14.8 in.) (in blower configuration w/side handle) Weight (dry) ------------------------------------------------ 4.9 kg (10.8 lb.)(w/o blower pipes) Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine Displacement ----------------------------------------------- 22.8 cc (1.39 cu. -
Page 9: Assembly
® 'N' V HRED PERATOR ANUAL SSEMBLY WARNING DANGER Never perform maintenance or assembly procedures with engine running or serious personal injury may result. BLOWER Install Blower Pipes 1. Align grooves in straight pipe with pegs on blower housing and slide pipe onto housing. - Page 10 4. Align grooves in discharge elbow with pegs on blower, and slide elbow (D) on to blower. Turn elbow counterclockwise to lock in place. Elbow must angle back toward operator position as shown. 5. Place debris bag opening over flared end of elbow, and cinch bag (E) securely with Velcro strap.
-
Page 11: Pre-Operation
Leaks can occur. Return unused fuel to an Echo premium Power Blend Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo engines sold in the past approved fuel storage container. regardless of ratio specified in those manuals. -
Page 12: Operation
PERATION STARTING COLD ENGINE 1. Stop Switch Move stop switch button (A) away from the STOP position. 2. Throttle Position Lever Move throttle position lever (B) forward to idle position. 3. Choke Move choke (C) to Cold Start ( ) Position. 4. -
Page 13: Starting Warm Engine
Move stop switch (A) to "STOP" position. WARNING DANGER If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using blower again. -
Page 14: Blower Operation
BLOWER OPERATION WARNING DANGER Always wear safety glasses, hearing protection and a face filter mask or serious personal injury may result. . Do not point the blower pipe in the direction of people or pets. Never operate unit without either housing cover grill or vacuum tube installed on unit securely, otherwise bodily harm may result. -
Page 15: Shred 'N' Vac ® Operation
® 'N' V HRED PERATOR ANUAL ® SHRED OPERATION WARNING DANGER Flying debris hazard. Never operate unit as a vacuum unless discharge elbow is installed and debris bag is securely cinched to elbow. Failure to follow instructions can result in serious injuries. 1. -
Page 16: Maintenance
ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If task is not listed, see your ECHO Dealer for repairs. -
Page 17: Air Filter
® 'N' V HRED PERATOR ANUAL AIR FILTER Level 1. Tools required: 25-50 mm (1-2 in.) medium bristle brush. Parts required: 90030 REPOWER Air and Fuel Filter Kit NOTE Clean daily. 1. Close choke (Cold Start Position). This prevents dirt from entering the carburetor throat when the air filter is removed. -
Page 18: Spark Plug
SPARK PLUG Level 2. Tools required: 3/4 in. Spark Plug deep socket, Feeler gauge (preferably a wire gauge), Parts Required: 90074 REPOWER Tune Up Kit 1. Remove spark plug and check for fouling, worn and rounded center electrode. 2. Clean the plug or replace with a new one. DO NOT sand blast to clean. -
Page 19: Exhaust System
® 'N' V HRED PERATOR ANUAL Cleaning Cylinder Fins 1. Remove four 3 mm hex screws, side handle and recoil starter. 2. Remove engine cover (four screws), pull cover away from engine. Clean cylinder fins to allow cooling air to pass freely. 3. -
Page 20: Shredder Blade
The cylinder exhaust port must be inspected and cleaned of excess carbon every 3 months or 90 hours of operation in order to maintain this engine within the emissions durability period. ECHO strongly recommends that you return your unit to your ECHO dealer for this important maintenance service. SHREDDER BLADE Level 1. -
Page 21: Debris Bag
High Altitude Adjustment High altitude adjustment is not required for proper operation of this engine. Level 2. Tools required: Screwdriver, tachometer (Echo P/N 99051130017) Parts required: None. NOTE Every unit is run at the factory and the carburetor is set in compli- ance with Emission Regulations. -
Page 22: Carburetor Adjustment
NGINE ROUBLESHOOTING n i l n i l n i l t l i f l f f t ' n c t i c t i t n I c t i i t c t l i f t l i f / s t t l i f... -
Page 23: Engine Troubleshooting
2. Place the stop switch in the "STOP" position. 7. Remove the spark plug and pour 7cc (1/4 oz.) of fresh, clean ECHO 2-stroke engine oil into the 3. Remove accumulation of grease, oil, dirt and debris cylinder through the spark plug hole. -
Page 24: Servicing Information
• Sending a check or money order for $2.00 per Parts Catalog or $1.50 per Operator's Manual made payable to ECHO, INCORPORATED. State on a sheet of paper the model number and serial number of the ECHO unit you have, part number of the manual (if known), your name and address and mail to address below. -
Page 25: P Age 9 Supplement Sup22203709
SUPPLEMENT TO OPERATOR'S MANUAL PART NUMBER X7531130400 (X753000390) 03/03 FOR MODEL: ES-230 S/N 005009117 - 05999999 PART NUMBER X7531131600 (X753000810) 03/03 FOR MODEL: ES-230 S/N 007001829 - 07999999 PART NUMBER X7531130700 (X753000370) 03/03 FOR MODEL: ES-231 S/N 006001248 - 06999999 Page 9 SSEMBLY VACUUM...