Advertisement
numbers in brackets refer to item numbers in the parts diagram.
4.1.
assembly
4.1.1.
Fit the sliding plate (36) to the platform (35), to cover the rear wheel removal aperture.
4.1.2.
Attach lead plate (37) to end of platform (35) using washers (23) and cotter pins (04).
4.1.3.
Fit the front wheel vice assembly (34) to the front of the platform (35) using bolts (33), washers (23) and nuts (30).
4.1.4.
insert the lift foot pedal (11) into the pump piston spindle (9) and insert the release foot pedal (10) into the release
valve spindle (5).
4.1.5.
Fit the baffle plate (32) with bolts (33) and washers (23) and nuts (30).
4.2.
Before first use
4.2.1.
leave the pump for one hour, to allow the oil to settle, before purging the system.
Note: Failure to allow sufficient time for the oil to settle could result in air remaining in the oil. In this event, the pump will not purge
completely first time and a second purge will be required.
4.2.2.
Purge the hydraulic circuit to eliminate any air in the system, by fully pressing the release valve pedal (10) and pumping the lift pedal
(11) 15 to 20 times.
4.2.3.
test the lift, unladen, by raising it to full height and then lowering it. depress release valve pedal (10) slowly to control the rate of
descent.
5. operatiNg iNStructioNS
WarNiNg! ensure that you read, understand and apply the safety instructions before use.
‰
WarNiNg! do Not attempt to overload the lift. the hydraulic pump is equipped with a safety valve which will prevent an excessive
‰
load from being lifted.
5.1.
Position the lift in a suitable area, checking that the surface on which the lift will stand is solid and flat (preferably concrete). ensure
that the adjusting screws (18) are screwed down to raise the castor wheels off the ground and thus prevent the lift moving during use.
5.2.
check that the lift is fully lowered, that the vice jaws are open and that the sliding plate is in position.
5.3.
Wheel the bike up the lead plate (37) and onto the platform so that the front of the wheel is just beyond the vice. Support bike on
centre/paddock stand as applicable.
note:1. if rear wheel is to be removed bike must be positioned so that the rear wheel is over the platform aperture.
2. there is a choice of mounting holes for the vice to cater for various sizes of bike.
5.4.
clamp front wheel in vice to prevent any movement of the bike.
5.5.
strap the bike securely to the platform.
5.6.
raise the lift by pumping the lift foot pedal (11).
5.7.
When the lift is fully raised pass the locking bar (22) through the holes in the front lifting arm (38) so that the lift cannot be inadvertently
lowered.
5.8.
When work is complete, check under the lift to ensure that there are no obstructions and that it is safe to lower the unit.
remove the locking bar from the front lifting arm and then sloWlY press the release valve pedal (10) to GentlY lower the lift.
imPortAnt: the speed of lowering is controlled by the release valve. the more the valve is opened the more rapidly the lift
descends. ensure the descent is slow and controlled.
5.9.
When the lift is fully lowered, open the vice jaws and remove the bike from the lift.
6. maiNteNaNce
6.1.
When the lift is not in use, it must be stowed in the lowest position to minimise ram and piston corrosion.
6.2.
Keep the lift clean and wipe off any oil or grease. lubricate all moving parts.
6.3.
Before each use check all parts. if any part of the lift is damaged or suspect remove lift from service and take necessary action to repair.
do Not use the lift if it is believed to have been subjected to abnormal load or shock. inspect and take appropriate action.
6.4.
Periodically check the ram and piston for signs of corrosion. clean exposed areas with a clean oiled cloth.
6.5.
the hydraulic oil level is checked as follows:
1) remove hydraulic unit from lift and stand upright.
2) remove vented plug from side of hydraulic unit. correct oil level is up to plug aperture - add hydraulic oil as necessary.
WarNiNg! only a good quality hydraulic oil, such as seAleY HYdrAulic oil, must be used. do Not use brake fluid.
‰
importaNt: Only fully qualified personnel should attempt maintenance or repair. Contact your authorised dealer.
importaNt: No reSpoNSibility iS accepted for iNcorrect uSe of the lift.
Hydraulic products are repaired by local service agents only. We have service/repair agents in all parts of the UK.
do Not return the product to us. Please call us on 01284 757500 to obtain the address and telephone number of your local agent.
if the product is under guarantee please contact your dealer.
© Jack sealey limited
Original Language Version
mC401.V3 | Issue 2 08/03/17
Advertisement
