Related Manuals for IBEA 3900
Summary of Contents for IBEA 3900
- Page 1 MOD. 3900 MANUALE D’ISTRUZIONE OWNER’S MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUAL DE USUARIO MANUAL DE INSTRUÇÕES INSTRUCTIEHANDLEIDING...
- Page 2 (ÍNDICE. PAG. 68 ) INLEIDING Beste cliënt, we danken u dat u voor een IBEA kwaliteitsproduct gekozen heeft. Vang de werkzaamheden nooit aan voordat u deze handleiding aandachtig doorgelezen heeft om een correcte gebruik van de kettingzaag mogelijk te maken en ongevallen te vermijden.
-
Page 3: Table Of Contents
2004/108/CE, 1997/68/CE AND TO THE NATIONAL REGULATIONS GOVERNING ITS TRANSPOSITION ABROAD: AND THAT IT HAS BEEN ISSUED WITH A “CE” CERTIFICATES, NO. MOD. 3900 = M.0303.15.5876 BY THE I.C.E (Notified certification body No. 0303 PALAZZO DEL VESCOVO - V. GARIBALDI,20 40011 ANZOLA DELL’EMILIA (BO) - ITALY... -
Page 4: Chain Saw Components
ENGLISH 2. CHAIN SAW COMPONENTS 1. Chain 12. Clutch housing/guide bar nut locking 2. Guide bar 13. Spiked bumper 3. Throttle trigger lockout 14. Chain catcher 4. Rear handle 15. Chain tension adjuster 5. Starter handle 16. Clutch cover 6. Air cleaner cover 17. -
Page 5: Symbol Interpretation
Wear safety head, eye and ear protection Use the chain saw with both hands Warning! Kickback it’s danger 4. SPECIFICATIONS MODEL IBEA 3900 38.0 DISPLACEMENT cm³ 1.8 / 2.5 POWER Kw / CV 3000 giri/min. IDLER RPM 13.500 giri/min. -
Page 6: For Your Precautions
2. IBEA recommends wearing hearing protection at all safety equipment such as harness, loops, strops, ropes times. If not followed, hearing loss can occur. You should and karabiners for himself and for the saw. - Page 7 Do not use excessive force when tightening the tank cap with the socket wrench as the tank cap is made of plastic. If there is any damage to the tank cap do not start the engine. Ask your IBEA dealer for a replacement cap.
- Page 8 ENGLISH 5. Do not operate a chain saw with one hand! Serious 1. Saw wrongly held too close to operator’s body. Kickback injury to the operator, helpers or bystanders may result time may be too fast even for a perfectly maintained from one-handed operation.
-
Page 9: Mounting Guide Bar And Chain
ENGLISH 3. Limit the number of hours of chain saw operation. Try 2. Do not let any person use your saw unless he has to fill a part of each work day with jobs other than chain read this operator’s manual and fully understands its sawing. -
Page 10: Fuel And Chain Oil
ENGLISH 7. FUEL AND CHAIN OIL FUEL AND LUBRICANT NOTE Whenever opening up the fuel tank, always loosen Fuel is a mixture of regular grade petrol and an aircooled the cap very slowly and wait for the tank pressure to 2-stroke engine oil of reputable brand name. - Page 11 ENGLISH STARTING THE COLD ENGINE - After starting the engine, squeeze throttle trigger (4) fig.3 slightly to release throttle latch and pull 1. Fill the fuel tank with fuel mixture (D) and fill the chain front hand guard towards (1) the operatore oil tank with chain saw oil (E).
- Page 12 ENGLISH CHAIN LUBRICATION TEST NON-MANUAL CHAIN BRAKE Hold the chain just above a dry surface and open the The non-manual chain brake stops the operation of the throttle to half speed for 30 seconds. A thinline of “thrown” saw chain in such a manner that kickback action produced oil should be seen on the dry surface.
-
Page 13: Cutting Instruction
ENGLISH 9. CUTTING INSTRUCTION The accepted way to hold the saw is to stand to the left of side. Then remove the saw for the second cut. Insert the the saw with your left hand on the side handle and with saw in the first cut very carefully so as not to cause your right hand on the top handle so you can operate the kickback. -
Page 14: Service
ENGLISH BUCKING NOTE If you have misjudged the effects of tension and Bucking is the sawing of a log or fallen tree into smaller compression, and cut from the wrong side, the timber pieces. will pinch the guide bar and chain and trap in it. 1. - Page 15 3. When the filter is dirty, replace it. installation of guide bar. 4. When the inside of the fuel tank is dirty, it can be cleaned by rinsing the tank out with petrol. NOTE When replacing guide bar or saw chain, ask your IBEA dealer.
- Page 16 4. By using the correct file size (4,0 mm round file) and a file holder, it is easier to receive a good result. 5. Consult your dealer IBEA for correct sharpening tools and sizes.
-
Page 17: Storage
ENGLISH 19.If the saw chain becomes soiled with resin for instance, WARNING clean it with kerosene and soak it in oil. Properly filed cutters are shown below: SWITCH OFF THE ENGINE BEFORE A) top plate angle 30° SHARPENING THE CHAIN. B) side plate angle 80°... -
Page 18: Limited Warranty
ENGLISH distribute the oil inside the engine; observe the piston WARNING location through the spark plug hole; pull the recoil starter handle slowly until the piston reaches the top of DO NOT STORE IN ENCLOSURE its travel and leave it there). WHERE FUEL FUMES MAY ACCU- 9. - Page 19 IBEA s.r.l. Via Milano, 15/17 - 21049 Tradate (VA) Tel. 0331-853611 Fax 0331-853676 email: ibea@ibea.it www.ibea.it...