Teledex Pearl S - Pan Euro User Manual

PACKAGE CONTENTS
Check to be sure that you have all of the following components in
your package (see figure below) :
• Telephone base unit • Handset coil cord
• Handset • Line cord
INSTALLATION
1) Plug one end of the handset coiled cord into the handset. Plug
the other end of the cord into the handset jack located on the
left side of the phone base. (Refer to diagram on reverse.)
2) Place the handset in the handset cradle. Plug one end of the line
cord into the jack on the back of your phone.
LINE
3) Plug the other end of the modular cord into the wall jack.
WALL MOUNTING
The Pearl S telephone can easily be attached to a wall mount plate.
1) Remove the wall mount clip (located on the front of the
telephone, above the speaker grill) by firmly pushing upward
(toward the hook switch.)
2) Rotate the clip 180 degrees, so that the side with the protruding
edge is towards the top of the telephone. This edge will help
hold the handset on the cradle.
3) Place the handset in the handset cradle.
4) Connect the line cord into the
phone. Route the line cord through channel on the bottom of
the telephone. Connect the other end of the line cord to the
jack on the wall mount plate.
5) Slip the phone onto the wall plate; slide the telephone down
so it is firmly in place.
USING THE DATA PORT
The data port is located on the right hand side of the telephone. Use
this jack to connect a computer or fax machine in parallel to the
same phone line to which the telephone is connected.
ADJUSTING THE RINGER VOLUME
Your Pearl S telephone has two ringer volume levels: "Low" and
"High." To adjust the ringer volume, slide the ringer volume switch
(located on the backside of the telephone) to the desired level.
HANDSET VOLUME CONTROL
There are three (3) volume levels for the handset volume. To increase
or decrease the handset volume, slide the handset volume switch
(located on the right hand side of the telephone) to the desired setting.
SPEAKER VOLUME CONTROL
To increase or decrease the speakerphone volume, move the speaker
volume slider control (located on the right hand side of the telephone)
until speaker volume is at a satisfactory level.
PLACING AND ANSWERING CALLS
To make a call, pick up the handset or press the
you hear the dial tone, dial the desired phone number. To answer an
incoming call, pick up the handset or press the
call, place the handset back on the base, or press the
again.
SWITCHING BETWEEN HANDSET AND SPEAKERPHONE
To switch from the handset to the speakerphone during a call, press
the key, and place the handset on the base. To switch from
SPEAKER
the speakerphone to the handset, lift the handset; the speakerphone
will automatically turn off.
USING REDIAL
The redial function allows you to redial the last dialed number. Pick
up the handset, or press the
SPEAKER
number will be dialed automatically.
USING FLASH
Flash supports custom calling services, such as call waiting. For
example, if you have subscribed to call waiting, press
an incoming call, without disconnecting the current call. Press
again to return to the first call.
• User guide
jack on the back of your
LINE
key. When
SPEAKER
key. To end a
SPEAKER
key
SPEAKER
key, and press the key. The
REDIAL
to answer
FLASH
FLASH
PEARL S
Guestroom Speakerphone
Users Guide (Pan Euro)
USING HOLD
To place a call on hold, press the
You may now hang up the handset without disconnecting the call.
To resume the call, press the
HOLD
The call will once again be active.
USING MUTE
Pressing the key will silence the handset or speakerphone micro-
MUTE
phone. You will be able to hear the other party, but they will not be
able to hear you. The LED will light. Press the
MUTE
resume your conversation.
PROGRAMMING GUEST SERVICE KEYS
Follow these steps to program a number into one of the three memo-
ry locations, for one-touch access to guest services, or for accessing
special PBX/Centrex services or features. Each memory location can
store up to sixteen (16) digits.
1) Lift the handset, listen for dial tone, and press the
(For key location, refer to diagram on reverse.)
2) Using the dial pad, enter the number you wish to store (up
to 16 digits in length.)
3) Press the guest service key where you would like the number
to be stored.
4) Press the key again to complete. Repeat as necessary for
STORE
subsequent guest service keys.
DIALING A STORED NUMBER
Pick up the handset or press the
then press the desired memory (guest service) key. The telephone will
automatically dial the stored number.
PROGRAMMING FLASH TIMING
NOTE – The following procedure should only be attempted by a
trained technician. If you are unsure of your ability to carry out this
procedure, please refer the procedure to such a trained technician.)
The flash timing on the Pearl S phone can be set at 100ms, 300ms
or 600ms, by using a jumper. This jumper is located under a hidden
cover at the top of the telephone. To access this cover, remove the
plastic overlay, undo the two screws, and remove the cover.
1) For 100ms flash, set the jumper at location
2) For 300ms flash, set the jumper at location
3) For 600ms flash, do not set any jumpers.
MESSAGE WAITING
The message waiting indicator flashes to indicate that there is a
message waiting. Consult your system administrator or service
provider for instructions on how to access these messages.
PACKAGE CONTENTS
BASE UNIT HANDSET
key. The LED flashes.
HOLD HOLD
key again, or press the
SPEAKER
key again to
MUTE
key
STORE
key, wait for a dial tone,
SPEAKER
.
J100/300
.
J100/300 and J300
COIL CORD
LINE CORD USER GUIDE
key.