Targus Bluetooth Comfort Laser Mouse Introduction Thank you for your purchase of the Targus Bluetooth Comfort Laser Mouse. This mouse uses Bluetooth technology which provides a seamless connection up to 33 feet (10 m) away. This is a plug and play device so no additional software is required.
Targus Bluetooth Comfort Laser Mouse Installing the Batteries 1. Remove the battery cover from the top of the mouse by using the notch on the back. Carefully lift the cover up as shown in the diagram. 2. Remove the battery safety clip by squeezing the center of the clip and sliding it back, towards the rear of the mouse.
Page 4
Targus Bluetooth Comfort Laser Mouse 3. Slide and lift to remove the battery holder as shown. 4. Insert the two AA batteries, making sure that the positive (+) and negative (-) ends of each battery match the polarity indicators inside...
Page 5
5. Replace the battery safety clip and by sliding it forward until it clicks into place and then replace the battery cover. 6. Turn on the mouse by pressing the power On/Off button on the bottom of the mouse. Hold for 3 seconds and then release.
Page 6
3 seconds. 1st LED 3rd LED If the connection is not established by the end of 60 seconds, the mouse will go into sleep mode. Click on any mouse button to exit from sleep mode. The pairing sequence will re-start automatically.
Targus Bluetooth Comfort Laser Mouse Power Saving mode: After an extended period of time, if the mouse is not used, it will automatically enter power saving mode to conserve power and increase battery life. Click on any mouse button to resume the normal operation. The mouse may take a few seconds to reconnect with your computer.
Targus Bluetooth Comfort Laser Mouse Initial Configuration Before you can begin using your Bluetooth mouse, you will first need to ® perform some initial setup steps. NOTE: PLEASE USE THE LATEST BLUETOOTH DEVICE DRIVER. INSTRUCTION SCREENS MIGHT VARY DEPENDING ON THE VERSION OF YOUR BLUETOOTH DEVICE DRIVER.
Page 9
Targus Bluetooth Comfort Laser Mouse Connecting with Bluetooth Software: WIDCOMM or Microsoft 1. Go to the Bluetooth Places icon located on your desktop or in the system tray and double click, then click Add a Bluetooth Device. (Windows XP) 2. The Bluetooth Wizard screen will prompt. Please follow the onscreen instructions.
Page 10
Targus Bluetooth Comfort Laser Mouse 3. Power on the mouse and it will automactically go into discovery mode. Click Next to continue pairing and the computer will search for the mouse. (Windows XP) 4. The confirmation window will appear after the computer finishes detecting the Bluetooth devices.
Page 11
Targus Bluetooth Comfort Laser Mouse 5. After selecting the correct device, the computer will finish establishing the connection. Please wait until the setup is completed. (Windows XP) (Windows Vista)
Page 12
1. Double click on the Bluetooth Manager icon in the system tray, and then click Add New Connection. 2. Power on the mouse and it will automactically go into discovery mode. Click Next to continue pairing and the computer will search for the mouse.
Page 13
Please wait until the search is completed. Choose the device you wish to connect. There may be more than one Bluetooth device detected. Select Bluetooth Wireless Mouse and click Next to continue. If the mouse is not detected, please make sure the mouse is in discovery mode and click Refresh.
Page 14
Targus Bluetooth Comfort Laser Mouse 5. The connection is established and setup is complete. The device is ready to use. If the connection is not successful, please click Back and search the device again. You can continue to add other Bluetooth devices or close the window.
Page 15
Targus Bluetooth Comfort Laser Mouse Bluetooth Software: Mac 1. Go to the Bluetooth icon located on your desktop or in the system bar and click the icon to begin setup. Select “Turn Bluetooth On” to activate the Bluetooth function on your Mac.
Page 16
“discovery” mode to connect. Power on the mouse and it will automactically go into discovery mode. 5. Your computer will begin to search for the mouse. Once the mouse is found, it will show up in the list. Highlight your mouse and press continue.
Page 17
Targus Bluetooth Comfort Laser Mouse 6. The Bluetooth mouse will now begin pairing. Click continue to proceed. 7. Congratulations. Your Bluetooth mouse is setup and ready to use. You can choose to setup another device or click Quit to exit setup.
Page 18
This can be downloaded from the following location: Visit www.targus.com to download and install the driver. Once installation is complete, open the driver software and select the desired setting for the scroll-wheel button. Close the driver software application and you’re ready to go.
1. Click Start/ Settings/ Control Panel/ System/ Hardware/ Device Manager 2. Check under “Bluetooth Devices” that a “Soft-Touch Bluetooth” is installed • Paired devices are always displayed in My Bluetooth Places, even if the mouse is out of range or not powered up.
Targus warrants this product to be free from defects in materials and workmanship for one year. If your Targus accessory is found to be defective within that time, we will promptly repair or replace it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss.
Targus Bluetooth Comfort Laser Mouse Regulatory Compliance This device complies with Part 15 of the FCC Rules and Industrial Canada RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 23
Targus Bluetooth Comfort Laser Mouse CAUTION LASER RADIATION. DO NOT STARE INTO THE BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. CLASS I LASER PRODUCT. NEVER POINT A LASER BEAM INTO A PERSON’S EYES OR VIEW A LASER BEAM DIRECTLY, AS PROLONGED EXPOSURE CAN BE HAZARDOUS TO THE EYES.
Page 24
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Targus is under license. All trademarks and registered QD ID : B012764 trademarks are the property of their respective owners.