Kygo B9 800 - Speaker Quick Setup Guide

Kygo B9 800 - Speaker Quick Setup Guide

Also See for B9 800:

Advertisement

Kygo B9 800 - Speaker Quick Setup Guide

Overview

Overview

Function Description
Power ON/OFF
  1. Press about 2s to power on, press again to power down.
  2. If power on, the WiFi mode set up. After WiFi setup finished, if no any action in 30mins, unit will enter to standby mode, but unit must keep listening for hotword if micphone is not muted.
VOL+ Press to turn up the volume, holding to keep going up.
VOL- Press to turn down the volume, holding on to keep going down.
Bluetooth
  1. Press the button once: if the speaker is playing then pause, if the speaker is paused then continue playing; If in Bluetooth pairing mode and no connection to any device, then exit pairing mode (in this state with no action, then auto exit pairing mode 10 mins later).
  2. Short press about 2s: enter Bluetooth pairing mode, if Bluetooth connected, then disconnected current connection and go to new Bluetooth pairing.
  3. Long press>5s: disconnect all Bluetooth connections and enter to pairing mode.
  4. Automatic reconnect last device in pairing mode.
  5. Keep connection in standby mode with 30mins, press Play button on Phone can wake up and streaming.
  6. In standby mode, after 30min, will disconnect Bluetooth connection.
Mic Mute Press button for Mic mute on and off.
Kygo Button Short press it will be connected to live streams from Kygo concert or festivals and so on.
Google Cast Stream Install Google Home app into phone, follow instruction of application for wifi setup and music streaming process.
Factory Default Resetting When the speaker power on, hold the vol- & vol+ at the same time for 15s, the speaker will power off by itself and reset factory default settings.
Source change WiFi streaming: Once detect signal from Google cast, auto switch to WiFi mode to play music. In standby mode, still can detect signal and wake up to stream music. Bluetooth: In Bluetooth mode, once unit be paired with device, can play music, if WiFi is playing music, stop or pause WiFi playing first. Aux IN: In AUX IN connection, Bluetooth is disabled; if you wake up with "OK, Google", then change to WiFi mode.

Features

Bluetooth 4.2

8 hours playing time

Google Assistant built-in

LED indicator for low battery

Compatible with Kygo Sound App

Multiroom playback across speaker with built in chromecast

Chromecast built-in

2,4/5 GHz Wifi support

360 degree sound profile

Great Sound quality with AAC®

IPX 7 - Waterproof and flotable

Google Voice Assistant

Just start with "OK Google", then ask it questions or tell it to do things like this:

"Play some jazz"
"Turn up the volume"
"Set a 13 minute timer for pizza"
"Do I need an umbrella today?"

Google Chromecast Built-in

Follow the three steps below to enjoy this feature:

  1. Connect a phone or tablet to the same Wi-Fi network as your speaker using the Google Home App.
  2. Cast podcasts, music, and more from 100+ Chromecast-enabled apps. Tap the Cast button in a Chromecast-enabled app to play
  3. Tap the Cast button in a Chromecast-enabled app to play music on your speaker.

Establish Bluetooth connection

The speaker is equipped with Bluetooth to allow wireless playback from any Bluetooth-enabled phone or tablet.

  1. If power on, Short press the button about 2s then enter Bluetooth pairing mode, blue led indicator fast flash.
  2. click the device name you entered during Google Home App setup on your device to pair with the speaker.
  3. After the speaker and your device are paired, you can stream music from your device to the speaker

Maintenance

Cleaning the Unit

warningEnsure the unit is fully unplugged from the mains socket before cleaning.

  • To clean the unit, wipe the case with a slightly moist, lint-free cloth.
  • Do not use any cleaning fluids containing alcohol, ammonia or abrasives.
  • Do not spray aerosol at or near the unit.

Do not ingest the battery, Chemical Burn Hazard

This product contains a button cell battery. If the button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using the product and keep it away from children/

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operatre the equipment.

This wquipment has been tested and found t comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement.
To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully

Troubleshooting

If you have problems using this product, check the following points before you request service, never try to repair the product yourself.
If you still have any problems, get support at www.kygolife.com/support.

PROBLEM SOLUTION
No Power Make sure that your speaker is plugged in and turned on.
No sound in Bluetooth
  1. Make sure that your Bluetooth device is turned on, Bluetooth is turned on, and the device name you entered during Google Home App setup is selected.
  2. Turn up the volume on your speaker.
  3. Turn up the volume on your Bluetooth device.
  4. Make sure that your Bluetooth device is not muted.
  5. Make sure that your speaker is paired to the correct Bluetooth device.
Cannot establish Bluetooth connection with this product
  1. Shorten the distance between your speaker and your Bluetooth device.
  2. Make sure that your speaker and Bluetooth device are both in pairing mode.
  3. Make sure that your Bluetooth device is not connected to any other device.
  4. Make sure that your speaker is not paired to any other Bluetooth device.
  5. Make sure that your Bluetooth device supports Bluetooth v4.2.
  6. Make sure that you have selected B9/800 when you entered during Google Home App setup.
  7. Turn your devices off, then on. Re-pair your speaker and your Bluetooth device.
Cannot connect to Wi-Fi
  1. Make sure that the wireless network is not disturbed by microwave ovens, DECT phones, or other neighboring Wi-Fi devices.
  2. Make sure that the speaker and your device shar the same network.
  3. Make sure that your router/modem is on and that you are within range of it.

Specification

Model KYGO B9 800
Power Adapter AC100-240V, OUTPUT 5V/2.1A
Battery Lithium 7.4V 2600mAh
Dimension W210mm*H75mm*D87mm
Frequency Response 75Hz-20kHz
Sound Pressure >85dB +/- 3dB
Net Weight

LED indicators

Function LED indicators
System Boost up 4RGB LEDs show white color slow breathing
  1. Red LED fast flash (Battery power is less than 20%)
  2. Red LED slow breathing (Solid Red when 100% charged)
Reach Max Volume 4 RGB all show white fast flash for two times
Bluetooth
  1. Blue LED fast flash (Pairing mode)
  2. Solid blue (Connected)
  3. Blue LED off (Disconnect)
Aux-in Solid Green
Mic Mute Micphone off: 4 RGB Orange
Factory Default Resetting 4RGB LEDs show white constant with fade in 0.5s

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Kygo B9 800 - Speaker Quick Setup Guide

Advertisement

Need help?

Need help?

Do you have a question about the B9 800 and is the answer not in the manual?

Questions and answers

Table of Contents