RockFire RF-2.4G - PC Combo PS2 Gamepad Manual

Package Contents

System Requirement

PC

1. IBM PC 586/PentiumII compatibles or higher
2. Available USB port or extension USB hub
3. CD-ROM drive
4. Microsoft Windows XP/ME/2000/98 recommended

PlayStation

1. PlayStation 2 / PSOne / PlayStation

Hardware Overview

Receiver

1. 1 Connection Button
2. 2 LED Indicator (One is connection indicator and another is low-battery indicator.)
3. 1 USB Connector for PC

Gamepad

Operation Reference

1. Gamepad Calibration
   Before using this gamepad, please rotate the sticks once to calibrate perfectly.
2. Connect Gamepad with Receiver
   Please follow below steps to connect the gamepad with the receiver.
   1. Press and hold the Connection/Vibration button of the gamepad until the Mode- LED twinkles with orange color.
   2. Press the button of the receiver to connect with each other.

> LED indicator:

3. Analog/ Digital Switching
   This gamepad is equipped with Digital and Analog modes. And there are some different features with PC and PlayStation modes in A/D modes as followings:

> PC

> PlayStation
You can switch between digital and analog modes. The Mode-LED turns ON with red color in Analog mode and with green color in Digital mode. When the gamepad is in Analog mode, the following buttons and sticks may operate in Analog fashion depending on the features supported by the software title. Refer to the software manual for details.

PlayStation2 format software
D-Pad / £Y,¡³,¡¼,¡µ / 2 ministicks / L1, L2, R1, R2

PlayStation format software
2 ministicks

4. Vibration Function
   You can switch the vibration function ON or OFF by pressing the Vibration Connection button.

>LED indicator:

5. Macro function
   There are four buttons (L2, L3, R2, R3) allowed being set as the macro buttons.
   Please follow below steps to set up the macro function.
   1. Press the Program button to set up the macro function.
   2. Press one of four buttons (L2, L3, R2, R3) which you want to set as a macro button.
   3. Press the buttons (D-Pad, ¡µ,£Y,¡¼,¡³, L1, R1, L2, R2, L3, R3, Start) in turn to set into the Macro function.
   4. Press the Program button again to finish the Macro function setup.

> LED indicator

6. Turbo function
   Please follow below steps to set up the Turbo function.
   1. Press the Program button.
   2. Press the buttons (△,Χ,□,○, L1, R1, Start) which you want to set with the Turbo function.

Note: If you want to remove the Turbo function, please repeat the above steps.

> LED indicator

7. LED Indicator while operating
   The Mode-LED indicates as the following table when you press any button:

8. Low -battery LED of the receiver
   When the Low-battery LED turns ON, please change new batteries.
   Note: The vibration function will be turned OFF automatically when this Low-battery LED ON.
9. Sleep & Wake Up
   When you stop operating this gamepad for some time (take a look at the below table), it is become to a "sleeping" mode to prevent consuming the battery. And you can wake up it by press one of the key-buttons as: Vibration/Connection, A/D, Macro/Turbo, Select, Start.

Installation Only for PC

Always install the software first, then the hardware subsequently.

Software Installation

This RF-2.4G gamepad is the software needed for your device setup, however, if you don't choose to install it, it is still operated without vibration function.

1. Insert the CD of this gamepad into your CD-ROM; wait for a few seconds for your computer to load the disc.
2. If your system is setup to automatically read a new inserted CD, then the auto run program is executed and the opening screen for installation appears. Please follow the on-screen instruction to install this gamepad step-by-step.
3. If your system doesn't launch the installation software automatically, please find the auto execute file "Install bat", which is located under the directory of your CD drive and click on it, then follow the on-screen instruction to install this gamepad.

The installed procedures administer as follows:

• Install Shield Wizard information: The system is ready to install, and click "Next ".
• The copyright declares: Select "Agree" and click "Next".
• User's information: Key in "User's name and Company". If your system is Window 2000/Xp, select an appropriate use limit.
• Confirm to start install: Press "Install".
• Finish the install: Press "Finish".

4. Upon completing software installation, restart your PC as the installation screen requested.

Hardware Installation

1. Plug the Mini-USB connect of the cable to the port on the receiver and another USB connect to the USB port on your computer.
2. After connected the monitor will show "Find a new hardware" and the standard USB driver will be located for you to finish the easy installation and play games immediately.
3. The system will add an item of this gamepad in the game-controller board automatically, and you can test the function of gamepad.

Importance & Attention

1. When this gamepad is used in PC, please ensure the Joystick ID of it "Joystick 1", if the USB port of this receiver is properly plugged but no any work.
2. The functions of all buttons may vary in different games. Before start game setting, always read your game manual carefully to approach the best game setting.
3. Please use the same brand of batteries to ensure there is a better efficiency.

All brand names mentioned in this manual are trademarks or registered trademarks of their respective companies.

For more information or any services are required, please visit us through the Internet link
Website: http://www.rockfire.com.tw
e-mail: service@r ockfire.com.tw

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download RockFire RF-2.4G - PC Combo PS2 Gamepad Manual