Page 2
OS-191 uNek 2 Thank you for purchasing the OSIM uNek 2. Before you start using the uNek 2, please read the operation manual thoroughly for the correct methods of usage, especially the section on safety. This manual should be kept on hand for easy reference. It is your guide to a safe and efficient operation.
Page 3
3) Disconnect the USB cable and remove it from the electrical outlet after charging. 4) Do not use or rest on the product while charging. 5) When the battery life span is over, contact OSIM Service Center for battery replacement. Do not replace the product battery yourself. Only use the battery provided.
Page 4
USB cable from the electrical • Do not use the product in outlet. Contact the OSIM Service Center for servicing. temperatures higher than 40°C. • Liquid is accidentally spilled •...
Page 5
Safety Safety precautions • Do not insert any object or flammable material into the • To ensure safe and correct usage product. This may result in an of the product, do not operate electric shock, malfunction or it without carefully reading this risk of fire.
Page 6
• Do not tamper with the USB cable or use the product with a damaged USB cable. If the USB cable is damaged, it must be replaced by OSIM Service Center or its authorized service agents.
Page 7
Names of parts and functions Main unit & accessory. 1. Power ON/OFF and Warmth switch 2. LED indicator 3. Micro USB port (remove the rubber cover) 4. Program selection button 5. Massage rollers (concealed by fabric) 6. Air valve (Press to ‘Close’ to allow inflation. Press to ‘Open’ deflate.) 7.
Page 8
Charging the product battery Massage program selection • Red LED indicator will flicker • Press the [ ] button to cycle to show the uNek 2 is low in through the 3 auto massage battery. programs. i. Relax (1 ‘beep’ sound •...
Page 9
This may cause the colour of fabric to fade. Do NOT attempt to repair your product For safety reasons, under no circumstances should you attempt to repair the product. If you suspect a malfunction, always call the OSIM Service Center for further assistance and information.
Page 10
If you encounter problems with the operation of the uNek 2, please check the following points to see if they can be rectified. If the uNek 2 still malfunction or does not work, please turn off the uNek 2. Contact OSIM Service Center* for servicing.
Page 11
The internal safety device may have been activated due to incorrect voltage. Contact OSIM Service Center for servicing. * Please visit us at www.OSIM.com for information on the nearest service center. Product warranty is valid only in the country of purchase.
Page 12
Specifications Specifications Model OSIM uNek 2 Model number OS-191 DC power (USB cable input) (Kindly ensure that the local Alternating Current (AC) voltage corresponds with product specified voltage) Auto timer 10/30 minutes Dimension 31 (L) x 30 (W) x 10 (H) cm Weight Approx.
Page 18
产品仅能使用直流电 (DC)。 • 发生雷电时,请勿使用本 • 不慎将液体泼洒或倾倒在产品上 产品。 时,请立即将 USB 缆线从电源 插座中拔除。 • 双手潮湿时,切勿安插或将 USB 缆线从电源插座中拔除。 • 请勿用重物压住 USB 缆线。 • 请勿将 USB 缆线缠绕于产品, 以免 USB 缆线受损。 • 电源插座有松脱的状况时, 请勿使用产品。 • 请勿损坏 USB 缆线或是在 USB 缆线受损的状况下操作产品。 如果 USB 缆线受损,必须由 OSIM 维修服务中心或专职 服务人员进行处理。...
Page 30
(DC)。 產品。 不慎將液體潑灑或傾倒在產品 • 上時,請立即將 USB 纜線從電 源插座中拔除。 雙手潮濕時,切勿安插或將 • USB 纜線從電源插座中拔除。 請勿用重物壓住 USB 纜線。 • 請勿將 USB 纜線纏繞於產品, • 以免 USB 纜線受損。 電源插座有鬆脫的狀況時, • 請勿使用產品。 請勿損壞 USB 纜線或是在 • USB 纜線受損的狀況下操作產 品。 如果 USB 纜線受損,必 須由 OSIM 維修服務中心或專 職服務人員進行處理。...
Need help?
Do you have a question about the uNek 2 and is the answer not in the manual?
Questions and answers