Related Manuals for Philips RC1974401
Summary of Contents for Philips RC1974401
- Page 1 Confidential Document Philips Electronics Singapore Pte Ltd User Manual Setup Procedures & Information For Used 2.4GHz RF Remote Control (RC1974401/01BRF) & 2.4GHz RF USB Receiver (OVU700003/01RF) Page 1 of 15...
-
Page 2: Table Of Contents
Confidential Document Philips Electronics Singapore Pte Ltd Table of contents FCC Statatement Page 3 of 16 Setup Procedures Page 4 of 16 Information For Used Page 12 of 16 General Page 13 of 16 Stuck key function Page 13 of 16... -
Page 3: Fcc Statatement
Confidential Document Philips Electronics Singapore Pte Ltd 1. FCC Statement FCC Part 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device maynot cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 4: Setup Procedures
Confidential Document Philips Electronics Singapore Pte Ltd 2. Setup Procedures Setup Procedures of 2.4GHz RF Remote Control and 2.4GHz RF USB Receiver Plug into USB port USB port 2.4GHz RF USB Receiver Picture 1: USB port and 2.4GHz RF USB Receiver plug into USB port. - Page 5 Confidential Document Philips Electronics Singapore Pte Ltd Picture 2: 2.4GHz RF Remote control with packaging (front and rear side). Press the hook down and lift up the lid Picture 3: Remove the battery lid by pressed the hook down the battery lid and lift it up.
- Page 6 Confidential Document Philips Electronics Singapore Pte Ltd Picture 5: Closed up the battery compartment with battery lid. Lift up the LCD display after release the catcher Press to right hand side to release the catcher Picture 6: Lift up the notebook LCD display by release the catcher.
- Page 7 Confidential Document Philips Electronics Singapore Pte Ltd Picture 8: Process of loading Windows Vista. Picture 9: Close the application as above by click the “X” icon at upper right hand side as Picture 10. Picture 10: The “X” icon located at right hand side, upper corner.
- Page 8 Confidential Document Philips Electronics Singapore Pte Ltd Picture 11: Using cursor to click the “Start” icon located at left hand side, lower corner. Picture 12: Select and click the “WordPad” application program. Page 8 of 15...
- Page 9 Confidential Document Philips Electronics Singapore Pte Ltd Picture 13: The “WordPad” application software. Picture 14: Press “Digit 5” and release the button on the 2.4GHz RF remote control Page 9 of 15...
- Page 10 Confidential Document Philips Electronics Singapore Pte Ltd Picture 15: The WordPad display “5” for press and release button Digit 5 on 2.4GHz RF remote control. Picture 16: After testing, before shutdown the note book, close all the application software as click the “X” icon located at upper right hand corner and after that, click the icon “Don’t Save”...
- Page 11 Confidential Document Philips Electronics Singapore Pte Ltd Picture 18: Click the “Shut Down” icon Picture 19: Notebook shutting down. Page 11 of 15...
-
Page 12: Information For Used
Confidential Document Philips Electronics Singapore Pte Ltd 3. Information For Used 2.4GHz RF Remote Control (RC1974401/01BRF) & 2.4GHz RF USB Receiver (OVU700003/01RF) Page 12 of 15... -
Page 13: General
Confidential Document Philips Electronics Singapore Pte Ltd General This remote control is a 2.4GHz RF remote control (RC1974401/01BRF) which will transmit RF protocol. It will work with 2.4GHz RF USB receiver (OVU700003/01RF). Stuck key function Stuck key means a key or multiple key has been pressed for a very long time in normal operating mode. -
Page 14: Key Press
Confidential Document Philips Electronics Singapore Pte Ltd Key press 3.4.1 Continuous key press When the key is press and held, the transmission will repeat at the timing described in 1.1.1.1 If more than 1 key is pressed, there will be no transmission 3.4.2... - Page 15 Confidential Document Philips Electronics Singapore Pte Ltd If it receives this pairing command, it will overwrite it’s own 24bit- ID with the new ID in this command. The USB receiver will acknowledge the successful operation to the remote control. After the acknowledgement is received by the remote control, it will overwrite it’s own ID with this ID as well, into the Eeprom.