Cantel Medical Medivators BF-30 Instructions

2-8-210
HOOKUP CONNECTION GUIDE
Using MEDIVATORS ® ADVANTAGE ® Automated Endoscope Reprocessors
ADVANTAGE HOOKUP DIAGRAM

Medivators Inc.
14605 28th Ave N.
Minneapolis, MN 55447
Ž
USA
Medivators BV
Sourethweg 11
6422PC Heerlen
The Netherlands

Œ
Each ADVANTAGE Hookup is comprised of multiple ports and connector assemblies.
Each port is labeled with a Port ID number (circled). This same number also identifies the
corresponding Connector Assembly.
CONNECTOR ASSEMBLY IDENTIFICATION CHART
Port ID Port Name Connector Assembly Description
 LEAK TEST Leak Test Connector Assembly
 JET/AUX Air/Water Connector Assembly
 BIOPSY Biopsy Inlet Connector Assembly
 AIR Air Probe Connector Assembly
 ELEVATOR Auxiliary Water Connector Assembly
 WATER Air/Water Connector Assembly
SUCTION Suction Connector Assembly

 EXTRA N/A
If a Connector Assembly needs replacement, locate the port number/name and use
the corresponding order number found in the chart above. Connector Assemblies are
specific to individual hookups.
If you have any questions regarding this hookup, in the U.S., please contact
MEDIVATORS Technical Support at 1-800-444-4729. Outside the U.S., please contact
your MEDIVATORS Distributor.
© 2015 Medivators Inc. 50098-850-EN/B

Suction Connector
Align and insert the end of the connector into the
suction valve port. Firmly push the connector until
it 'clicks', then push the "LOCK" button until there
is another 'click'. To remove, press the "RELEASE"
latch (make sure the "LOCK" button pops up). Tilt
‘
the connector towards the V-notch of the scope
port while pulling the connector out.
’
“
Biopsy Connector
Align the biopsy connector
disc over the biopsy inlet
Order Number
and push down to compress
H28210-1
spring and slide the frame
forward to fully engage.
NA
H28210-3
NA
DESIGNATED HOOKUP FOR THE FOLLOWING ENDOSCOPES*:
NA
NA
BF-30 BF-240AWY1
BF-40 BF-260
H28210-7
BF-140 BF-6C240
BF-160 BF-6C260
N/A
BF-180 BF-MP160
BF-200 BF-MP160F
BF-240 BF-MP60
* This list of corresponding endoscope models is subject to change without notice. For a full list, please go to:
www.medivators.com/hookuplookup
Representative endoscope for illustrative purposes only. For exact
port locations, refer to endoscope manufacturer's instruction guide.
READ ALL INSTRUCTIONS PRIOR TO CONNECTION
Locate the endoscope port and follow the instructions for attaching the
corresponding Endoscope Connector. All connectors must be attached.


BF-P30 BF-P200 BF-1T30 BF-1T180
BF-P40 BF-P240 BF-1T30D BF-1TQ180
BF-P60 BF-P290 BF-1T40 BF-1T200
BF-P150 BF-Q180-AC BF-1T60 BF-1T240
BF-P160 BF-Q190 BF-1T130 BF-1T260
BF-P180 BF-TE2 BF-1T150 BF-Q180
BF-P190 BF-XP160 BF-1T160 BF-XT30
Leak Test Connector
Align the slot on connector
with the pin on the scope.
Push on and turn clockwise
to engage.

BF-XT40 ENF-VT
BF-XT160 ENF-VT2
BF-F260 LTF-160
BF-H190 LTF-240
BF-XP190 MAF-TM
BF-1TH190
BF-P260F