Download Print this page

Advertisement

Quick Links

Bitspower Cuboid Reservoir 180
Accessories
1
BPTA-WTSC180-CLBK
2
Support
3
M3x10mm Screw
4
M4x10mm Screw
1 SET
Digital RGB PIN on
other equipment.
DRGB Multi Function Controller
(Not included)
2 PCS
4 PCS
4 PCS
V1
1
motherboard or
1
motherboard
2
BPTA-DRGBMFC
[ 1 ]
instruction manual
2

Advertisement

loading
Need help?

Need help?

Do you have a question about the Cuboid Reservoir 180 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Bitspower Cuboid Reservoir 180

  • Page 1 Bitspower Cuboid Reservoir 180 Accessories BPTA-WTSC180-CLBK 1 SET Digital RGB PIN on motherboard or other equipment. motherboard BPTA-DRGBMFC DRGB Multi Function Controller (Not included) Support 2 PCS M3x10mm Screw 4 PCS M4x10mm Screw 4 PCS [ 1 ]...
  • Page 2 Assembly steps step 1 step 2 step 3 step 4 [ 2 ]...
  • Page 3 24-hour leaking test with only the pump connected to the power supply. Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.
  • Page 4 使用說明書 Bitspower Cuboid Reservoir 180 配件 BPTA-WTSC180-CLBK 1 組 請接 主版或 其他設備的 DRGB 插槽 主版 BPTA-DRGBMFC DRGB 控制器 ( 不包括 ) 支架 2 支 M3x10 毫米螺絲 4 支 M4x10 毫米螺絲 4 支 [ 4 ]...
  • Page 5 組裝步驟 步驟 1 步驟 2 步驟 3 步驟 4 [ 5 ]...
  • Page 6 注意 跑水前,請先確認所有零件已安裝在正確的位置上,在不開主機,單開水泵的 情况下,進行 24 小時的跑水測試, 確保無漏水情况後再開主機,避免發生漏 水而導致電腦零件的損壞。 本公司保留對產品的設計更改以及解釋的權力,如有更動恕不另行通知,產品 顏色與配件以實物為準。 當使用測氣產品測試水路時 , 為避免由于壓力過大導致產品損壞 , 輸入的壓力 請不要超過 0.5kg/cm (Bar), 如因壓力過大造成產品損壞 , 將由客戶自行承 擔 . 嚴禁客戶在水路有水及水泵開啟的情況下進行氣體飽壓測試。 Bitspower 建議消費者使用蒸餾水、純凈水,加入 Bitspower 的染劑作為水冷 液使用;如客戶自行選購的水冷液導致電鍍層剝落、水道堵塞、水泵轉動不正 常、水箱管破裂或密封圈變型以致漏水等及其它不可抗力之問題時,消費者自 行承擔相關產品責任。未注水前,請勿啟動水泵電源。 [ 6 ]...
  • Page 7 使用说明书 Bitspower Cuboid Reservoir 180 配件 BPTA-WTSC180-CLBK 1 组 请接 主版或 其他设备的 DRGB 插槽 主版 BPTA-DRGBMFC DRGB 控制器 ( 不包括 ) 支架 2 支 M3x10 毫米螺丝 4 支 M4x10 毫米螺丝 4 支 [ 7 ]...
  • Page 8 組裝步驟 步骤 1 步骤 2 步骤 3 步骤 4 [ 8 ]...
  • Page 9 注意 跑水前,请先确认所有零件已安装在正确的位置上,在不开主机,单开水泵的 情况下,进行 24 小时的跑水测试, 确保无漏水情况后再开主机,避免发生漏 水而导致电脑零件的损坏。 本公司保留对产品的设计更改以及解释的权力,如有更动恕不另行通知,产品 颜色与配件以实物为准。 当使用测气产品测试水路时 , 为避免由于压力过大导致产品损坏 , 输入的压力 请不要超过 0.5kg/cm (Bar), 如因压力过大造成产品损坏 , 将由客户自行承 担 . 严禁客户在水路有水及水泵开启的情况下进行气体饱压测试。 Bitspower 建议消费者使用蒸馏水、纯净水,加入 Bitspower 的染剂作为水冷 液使用;如客户自行选购的水冷液导致电镀层剥落、水道堵塞、水泵转动不正 常、水箱管破裂或密封圈变型以致漏水等及其它不可抗力之问题时,消费者自 行承担相关产品责任。未注水前,请勿启动水泵电源。 [ 9 ]...

This manual is also suitable for:

Bpta-wtsc180-clbk