Français - Bosch Professional GTA 600 Original Instructions Manual

Extra tools required (not included in the delivery):
– Cross-headed screwdriver
– Open-end spanner (13 mm)
Assembling the saw stand (see figures A1−A2)
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material.
– Open the swing latch (1) and extend the base frame (3).
– Insert the saw stand legs (4) into the square pipes in the
base frame (3) until they are aligned with the assembly
holes.
The saw stand legs must point outwards here.
– Screw together the saw stand legs and the base frame us-
ing the nuts and bolts in the fastening set (5).
Securing the power tool (see figures B1–B3)
– Fold up both clips (2).
– Push the rear housing frame (6) of the power tool so it
lies entirely beneath the clips (2).
– Centre the power tool on the base frame (3).
– Hook the bracket of the swing latch (1) over the fixing
clip (7) and fold down the lever of the swing latch to se-
cure the power tool.
Operation
Working Advice
Always hold the workpiece firmly in place, especially long,
heavy pieces. Once the workpiece has been cut, the centre
of gravity may be displaced, causing the saw stand to tip
over.
Do not overload the saw stand. Always observe the max-
imum load bearing capacity of the saw stand.
Transport (see figures C1–C3)
The power tool must not be mounted on the saw stand
u
when the saw stand is being folded up or unfolded.
You can fold up the saw stand for transporting.
– Remove the power tool.
– Fold down both clips (2).
– Fold up the saw stand.
– Hook the bracket of the swing latch (1) over the other
side of the base frame (3) and push down the lever of the
swing latch to secure the power tool.
Maintenance and Service
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
Bosch Power Tools
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Disposal
Saw stands, accessories and packaging should be recycled
in an environmentally responsible manner.
Français
Consignes de sécurité
Consignes de sécurité générales
Lisez tous les avertissements et instructions
joints au support de travail ou à l'outil élec-
troportatif à monter. Le non-respect des ins-
tructions et consignes de sécurité peut provo-
quer un choc électrique, un incendie et/ou en-
traîner de graves blessures.
Consignes de sécurité pour supports de travail
Débranchez l'outil électroportatif de la prise secteur
u
et/ou retirez l'accu avant de procéder à des réglages
et à des changements d'accessoires. La mise en route
intempestive des outils électroportatifs est une cause fré-
quente d'accident.
Installez correctement le support de travail avant de
u
fixer l'outil électroportatif. Un montage correct est pri-
mordial pour disposer d'une bonne stabilité et exclure
tout effondrement du support.
Fixez l'outil électroportatif de manière stable et sûre
u
sur le support de travail avant de l'utiliser. Un outil
électroportatif qui glisse sur le support de travail peut en-
traîner une perte de contrôle.
Placez le support de travail sur un sol ferme, plan et
u
horizontal. Si le support de travail risque de se déplacer
ou de basculer, il n'est pas possible de scier en toute sé-
curité et de bien guide la pièce.
Français | 7
1 609 92A 8YG | (19.07.2023)