1. Manuals
  2. Brands
  3. MORITEX Manuals
  4. Controller
  5. MLEK-A120W1LRD
  6. Instruction manual

MORITEX MLEK-A120W1LRD Instruction Manual

Led controller for mg-wave
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
English

Table of Contents

1. Introduction
Basic System Configuration
Equipment Control
Installation
1. Introduction
Please read this instruction manual carefully, before starting operation. Keep this book for the whole
product lifetime, and store it in a place easily accessible.
Meanings of Warning Symbol
WARNING
LED Controller for MG-Wave
MLEK-A120W1LRD
INSTRUCTION MANUAL
-
Table of Contents
13
13
14
14
15
15
16
16
16
17
The following warning symbol is used in this manual.
Be sure to fully understand the contents of the warning.
This warning marking indicates a potentially hazardous situation, which can
result in hazard to the operator or damage to the unit, if the directions of this
Instruction Manual are not followed.
-
External Signal Connector
Troubleshooting
13
17
17
19
19
19
20
21
22
23
24

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MLEK-A120W1LRD and is the answer not in the manual?

Questions and answers

Related Manuals for MORITEX MLEK-A120W1LRD

Summary of Contents for MORITEX MLEK-A120W1LRD

  • Page 1: Table Of Contents

    English LED Controller for MG-Wave MLEK-A120W1LRD INSTRUCTION MANUAL Table of Contents Table of Contents 4. Connections 1. Introduction External Signal Connector Precautions for Correct Use Connector for Illuminator Warranty 5. Maintenance Confirming Package Contents Troubleshooting 2. Features 6. Specifications 3. Installation...

  • Page 2: Precautions For Correct Use

    MORITEX shall not be responsible for indirect or consequential damages, in any way related to this product. The responsibility of MORITEX for any act shall not exceed the price of this product. The warranty is limited to business and use in Japan. Please inquire to MORITEX about warranty overseas.

  • Page 3: Confirming Package Contents

    ※2 An attached AC cord set is an AC cord set for exclusive use of this product. Other than this product, please do not use it. 2. Features Applicable Illuminators ※1,2 Requirements for applicable MG-Wave Illuminators (made by MORITEX) : Illuminator of up to 1.2 [A] /4pin Output Number of output channels: 1 channel Manual illuminance adjustment function It is possible to adjust the illuminance of the Illuminator by using the Output Control SW on the front-panel.
  • Page 4 3. Installation Basic System Configuration ・ This Unit is dedicated for use with/for connection to the MG-Wave Illuminator. ・ For external control, it is possible to connect an external apparatus via the External Signal Connector. ※ The cables for connection to the EXT Connector and to the Illuminator are supplied as Optional Item (MC-EXC-02, M-RCB4**L).

  • Page 5: Installation

    Installation Install horizontally on the rubber feet at the bottom of the unit. ※ Install the unit in such a way, that adequate space is left free for ventilation. Keep space of at least 10mm around the main body. ※ Be sure to install the unit in such a way that the Power Switch can be operated easily and the Mains Plug can be pulled out without hindrance, in case of emergency.
  • Page 6 Definition of “H” and “L” Signal Photo-coupler in the Power Supply Connection condition Connected to the GND Open or Connected to the Vcc ON/OFF signal 10pin Input signal State of the Illuminator Truth table of External Control External signal COMMON (9pin) ＋ State of the 1pin 2pin...

  • Page 7: Connector For Illuminator

    Connector for Illuminator (for MG-Wave Illuminator) Model Output Connector of the Unit Connector of the Illuminator SMP-04V-BC (made by JST) SMR-04V-B (made by JST) or its equivalent Pin assignment: Connector for Illuminator (OUT) Function / Identification ※1 Output Current (＋) ※2 Sensor (＋) ※2...

  • Page 8: Specifications

    ※3 An object equal to or more than a diameter of 2.5mm does not reach hazardous parts inside the unit. The unit is not protected against invasion of water. ※4 MLEK-A120W1LRD and all Optional Items, except stated explicitly do comply to these European Standards upon which CE marking is declared. Additionally, please use a ClassⅠpower supply cord set which confirms to CE marking in order to conform the unit to CE marking.

  • Page 9: Optional Items

    ○ MC-EXC-02 (length:2m, output side unattached) (optional sales) ※1 Please inquire to MORITEX about cable different in length. ※2 up to A250V Use a power cable that conforms to the standards of the country or region in which it will be used.

  • Page 10: Dimensions

    Dimensions...

  • Page 11: Others

    1. Do not dispose equipment and/or parts of the equipment as unsorted municipal waste but collect them separately. 2. Before disposal of the equipment and/or parts of it, please contact MORITEX for any return or disposal methods/systems. 3. This symbol indicates separate collection of electrical and electronic equipment. Do not dispose equipment and/or parts of the equipment as unsorted municipal waste.

  • Page 12: Appendix

    《Appendix》 ・If there are any unclear points or if you have any questions, please feel free to inquire MORITEX. For repair or after sales service, please contact any MORITEX office or the sales office where you have purchased the unit.
  • Page 13 TEL 048-218-2534 / FAX 048-462-6713 〒351-0024 埼玉県朝霞市泉水 3-13-45 E-mail : moritex.mvs@moritex.com URL : www.moritex.co.jp For inquiry, please contact to: MORITEX Corporation MORITEX Technologies (Shenzhen) Co., Ltd. 3-13-45, Senzui, Asaka-shi, No.20, Guiri Road, Daping Village, Saitama 351-0024 Guanlan, Longhua New District, Japan Shenzhen, 518110...

Table of Contents