Related Manuals for ICAN SEH400RB
Summary of Contents for ICAN SEH400RB
- Page 1 Brushless Motor Driver SEH400RB _________________________________________________________________...
-
Page 2: Table Of Contents
Brushless Motor Driver SEH400RB Catalogue 1 Brief Instruction ............................2 1.1 Features ..............................2 2.1 Electrical Performance .........................2 4 Driver port and function description .......................3 4.1 Driver port ............................3 4.2 Terminal Description ........................... 4 4.3 Description of external control signal circuit ..................4 4.4 Output circuit description ........................ -
Page 3: Brief Instruction
Brushless Motor Driver SEH400RB BLDC MOTOR DRIVER SEH400RB 1 Brief Instruction The SEH400R BLDC Driver is suitable for high voltage three-phase BLDC Motor with a power of 400W and below. This product has display, easy to operate, supports RS-485 communication protocol, can provide built-in potentiometer speed regulation, external potentiometer speed regulation, analog voltage speed regulation. -
Page 4: Driver Port And Function Description
Brushless Motor Driver SEH400RB 3 Mechanical Dimensions Unit: mm 4 Driver port and function description 4.1 Driver port... -
Page 5: Terminal Description
Brushless Motor Driver SEH400RB 4.2 Terminal Description Signal Terminals Description Power+ Power input Power- Ground Motor U Motor V Motor lines Motor W Ground +5VE Hall sensor + Motor hall sensor Hu Motor hall lines Motor hall sensor Hv Motor hall sensor Hw... -
Page 6: Output Circuit Description
Brushless Motor Driver SEH400RB The external potentiometer SV input wiring is shown below： The external analog SV input wiring is shown below: 4.4 Output circuit description ALM and SPD terminals as below, its connection mode with PLC is related to the type of PLC input... -
Page 7: Introduction To Panel Functions
Brushless Motor Driver SEH400RB 5 Introduction to panel functions 5.1Panel functions Operation Functions Description mode Display Speed display Display Temperature display Drive cooling temperature display 0. Internal knob speed regulation Speed regulation mode 1. External analog speed regulation selection 2. Key speed regulation or 485 speed regulation Step size is 100RPM;... -
Page 8: Panel Introduction
Brushless Motor Driver SEH400RB 5.2 Panel introduction 5.3 Drive panel control settings... - Page 9 Brushless Motor Driver SEH400RB Note: All settings will be saved automatically immediately, even power off without loss.
-
Page 10: Start And Stop
Brushless Motor Driver SEH400RB 6.Function setting of external control port. 6.1 Start and stop EN and GNDE are disconnect by default, When the power is turned on, the motor will not rotate. There are two ways to start the motor: 1. - Page 11 Brushless Motor Driver SEH400RB 1. External potentiometer speed regulation. 10KΩ is recommended to adjust the speed. Connect the central pin of the external potentiometer to the SV terminal, and connect the other two pins to the GNDE port and the +5VE port respectively.
-
Page 12: Rs485
Brushless Motor Driver SEH400RB 6.4 RS485 The communication function of this driver adopts Modbus protocol, which conforms to the standard GB/T 19582.1-2008. Using RS485-based two-wire serial link communication, the physical interface adopts 3.81mm, 3PIN plug-in terminal, the terminal definition is shown in the figure below, and three wires need to be connected: B, A, GNDE. - Page 13 Brushless Motor Driver SEH400RB Refer to the following table for the address of read / write register： READ Access Access Slave Function Access address address Check Value Defaul address code data Read parameters Range t value Unit (1byte) (1byte) (2byte)
- Page 14 Brushless Motor Driver SEH400RB The write register address can refer to the following table: WRITE Slave Function Access Access Value Default address code address data Check Write parameters Unit Range value (1byte) (1byte) (2byte) (2byte) (2byte) 0X0054 0X0000 Speed adjusting mode...
- Page 15 Brushless Motor Driver SEH400RB 7Alarm description and fault handling 7.1Alarm code description When over voltage, or the signal of the Hall sensor is wrong, etc., the following situations will occur: 1. The ALM port of the driver is automatically connected to the GNDE port, the ALM port becomes low level, and an alarm signal is sent to the upper computer (In this case, wiring operation is required to send a signal to the upper computer).
-
Page 16: Alarm Reset
Brushless Motor Driver SEH400RB 7.2ALARM RESET If the above solutions don’t work, follow the operations below to reset the alarm signal 1. MODE->P-05->SET to check the alarm code, then press SET to reset the alarm. 2. Cut off the power supply, then power on again after 1 minute, the alarm can be released. -
Page 17: After Sales Service
Brushless Motor Driver SEH400RB After Sales Service Warranty: The warranty is 12months from the date of shipment. We offer free technical support during the time. Repair progress: （1）Contact the sales to tell the details. （2）Send back the product to: Room 401, Building 2, No. 7, Xinhe Shengfeng Road, Wanjiang Street, Dongguan City, Guangdong Pr...