Related Manuals for CLINTON INDUSTRIES 80110
Summary of Contents for CLINTON INDUSTRIES 80110
- Page 1 U S E R M A N U A L OPEN BASE, POWER, CHANGING TABLE Limited Warranty ON FRAME & ELECTRICAL COMPONENTS Limited Warranty CLI-MA-078 ExamTablesDirect.com Shop tables & accessories at...
-
Page 2: Table Of Contents
In no event shall Clinton Industries’ liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, or its documentation or errors in its documentation. -
Page 3: Intended Use
Clinton Open Base, Power, Changing Table has no field serviceable parts. If failure occurs, unplug the table from the wall outlet and contact Clinton Industries, or your local Clinton distribution office. Please provide the following information before calling Clinton regarding an in or out of warranty problem. -
Page 4: Symbols, Classification, Rating & Mode Of Operation
SYMBOLS, CLASSIFICATION, RATING & MODE OF OPERATION SYMBOLS For safety purposes, please familiarize yourself with the following symbols and their meanings which appear through this manual. Operating Instructions Pay particular attention to Cautions and Warnings throughout this manual. Potentially hazardous and harmful situations to users, patients and property can occur if these cautions and warnings are ignored. -
Page 5: Important Safety Guidelines
Always connect these tables to a properly grounded 120V outlet. The power supply and controller contains no serviceable parts. If failure occurs, unplug the table from the wall outlet and contact Clinton Industries, or your local Clinton distribution office. ExamTablesDirect.com... -
Page 6: Product Description
PRODUCT DESCRIPTION: Open Base, Power, Changing Table MODEL: 80110-60 SPECIFICATIONS Length 60" Width 27" Height Range 18" – 35" Load/Force Capacity 400 lbs. Upholstery knit-backed vinyl Warranty 5-year limited Voltage 120V Safety Listings MODEL: 80110-72 SPECIFICATIONS Length 72" Width 27"... -
Page 7: Unpacking & Setup
Clinton uses every packaging option available to insure that equipment arrives at its destination in factory condition, however, Clinton Industries has no control over third party handling once it leaves our facilities. Report any visible damage to Clinton and the shipping carrier immediately. -
Page 8: Cleaning
CLEANING CLEAN BEFORE USING (All Models) It is important to thoroughly clean tables according to facility standards before it is put into service. See cleaning suggestions below. WARNING Make certain that the table's power cord is disconnected from the outlet before cleaning with any liquid. -
Page 9: Installation
INSTALLATION All Clinton Open Base, Power, Changing Tables are shipped fully assembled. Simply plug the power cord into a grounded (three-prong) 120V outlet and your power table is ready for operation. Make certain the power cord is readily accessible, if the table needs to be disconnected for any reason. Power cord and foot control should be located where they will not present a tripping hazard. -
Page 10: Operation
OPERATION OPERATOR/PATIENT/OTHERS POSITIONING The operator’s position should be standing within a close proximity to the patient with a full view of both the patient and the immediate area surrounding the table. The patient should be sitting or lying on the table’s surface with the backrest either in the inclined or prone position. Others, located in the area, should be clear of the table during operation. - Page 11 OPERATION UPHOLSTERED SIDE RAILS TO LOWER THE SIDE RAILS, simply pull out the spring-loaded knob and gently lower the rail until the spring loaded knob clicks into place. It should be perpendicular to the top. TO RAISE THE SIDE RAILS, simply pull out the spring-loaded knob and swing the side rails up until the spring knob clicks into place.
- Page 12 OPERATION LOCKING CASTERS The locking mechanism can be engaged by using your foot to depressing the tab located at the rear of each caster. This action locks the swivel of the caster and acts as a brake to minimize movement of the wheel.
-
Page 13: Periodic Visual Inspections/Model & Serial Number
PERIODIC VISUAL INSPECTIONS/MODEL & SERIAL NUMBER PERIODIC MONTHLY INSPECTION • Inspect all electrical cords and connections for damage or wear. • Check that all fasteners are in place and securely fastened. • Make certain that the hi-lo function of the table is in proper working condition. •... -
Page 14: Warranty
Clinton Industries located at 525 East Market St, York, PA, 17403. If replacement parts are deemed necessary by Clinton Industries within (1) one year of the purchase date, all new parts and shipping will be covered by Clinton Industries. Thereafter in warranted years (2) two through (5) five, all shipping charges of replacement parts or replacement product (at our discretion) covered under this warranty will be the responsibility of the purchaser. -
Page 15: Specifications/Products
Upon completion of the equipment’s life cycle, discard components in a manner which complies with both local and federal guidelines so as to not create a hazard to others or the environment. Model: 80110-60 Table Weight ......................280 lbs. Max (127 kg) Total Load Capacity (including force) ................400 lbs. (181 kg) Overall Length .......................... -
Page 16: Contact Information
CONTACT INFORMATION 525 East Market Street York, Pennsylvania 17403 800-441-9131 • 717-848-3519 Toll-Free Fax 866-522-1233 Fax 717-843-5871 www.clinton-ind.com Printed in the USA © Copyright 2022, Clinton Industries, Inc. ExamTablesDirect.com Shop tables & accessories at...
Need help?
Do you have a question about the 80110 and is the answer not in the manual?
Questions and answers