Subscribe to Our Youtube Channel
Related Manuals for ENFORCER 30
Summary of Contents for ENFORCER 30
- Page 1 Operation and Maintenance Manual Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 1 Copyright 2020...
-
Page 2: Table Of Contents
- Preventative Maintenance Checks and Services Chapter 4 Page - Training Chapter 5 Page - Maintenance - Servicing and Maintenance Activities 12-16 - Troubleshooting 16-17 Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 2 Copyright 2020... - Page 3 If the product has been altered, modified or repaired in any way, or if the failure is the result of misuse, abuse or misapplication without the prior consent of Enforcer One, LLC, this warranty shall be void and Enforcer One, LLC shall have no obligation to repair or replace the failed product.
- Page 4 MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. No person or entity is authorized to bind Enforcer One, LLC to any other warranty obligation or liability to distributer, purchaser or any third party for any loss of profits, economic loss, indirect, incidental, punitive, special or consequential damages whatsoever and howsoever caused.
- Page 5 Safe Operating Requirements – continued DO NOT attempt to use this or any Enforcer One, LLC Enforcer line of product(s) if you are tired, injured or under the influence of drugs, medication or alcohol. keep children and bystanders away from the area when Enforcer One, LLC Enforcer line of product(s) are in-use.
-
Page 6: System Description
Enforcer 30 produces air aspirated foam that provides a thick vapor sealing blanket that will inhibit re-ignition. The Enforcer 30 will produce up to 200 gallons of finished foam with discharge duration of up to 2 minutes. The system can be easily recharged by the end user. -
Page 7: Operating Instructions
Preventative Maintenance Checks & Services (PMCS) 3-4. a. It is recommended that the PMCS CHECKLIST be completed every month. b. Personnel conducting the PMCS should be thoroughly familiar with the Enforcer 30 system and the information contained in this manual. Enforcer One, LLC FIREBULL®... -
Page 8: Preventative Maintenance Checks And Services
2. Remove, recharge and replace the Air Cylinder. The Air Cylinder should normally be left in the closed position. Note any other Problems: Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 8 Copyright 2020... - Page 9 4. Check for obstruction in discharge hose b. Shut Down Procedures 1. Close the Air Cylinder Valve 2. Depressurize the system 3. Secure discharge hose Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 9 Copyright 2020...
-
Page 10: Training
Chapter 4 Training Training Program 4-1. a. Training on the Enforcer 30 should be conducted or reviewed annually for all operators b. Maintenance personnel should complete initial training and refresher training as required c. Trainers should be thoroughly familiar with the system, fire behavior, hazard identification, and basic firefighting techniques d. -
Page 11: Maintenance
Technical Assistance 5-2. Maintenance personnel should contact Enforcer One, LLC whenever any problem arises that cannot be solved using the information in this manual or when unusual situations are encountered or expected. - Page 12 Enforcer 30 Maintenance Log Preventative Maintenance Checks and Services (PMCS) Refer to Chapter 5 – Maintenance for specific activities Maintenance Date Performed By Notes/Comments Activity Completed Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 12 Copyright 2020...
- Page 13 Air Cylinder – Annually Visual Inspection Air Regulator Every 2 years Inspection Air Cylinder Every 5 Years Hydrostatic Test Premix Cylinder Every 5 Years Hydrostatic Test Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 13 Copyright 2020...
- Page 14 Unscheduled Maintenance Maintenance Activity Date Performed Comments/Notes Completed Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 14 Copyright 2020...
- Page 15 9. Important Note: The Premix Tank Manifold should be tightened by hand. Do not use any wrenches or Teflon tape or thread sealant on any of the Premix tank fittings. Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 15 Copyright 2020...
-
Page 16: Troubleshooting
Fill the Premix Tank with FIREBULL® Fluorine Free Foam Freeze Protected Premix solution whenever temperatures are below 32 degrees Fahrenheit. FIREBULL® Fluorine Free Foam is a solution made by Enforcer One, LLC. The Pre-Mix solution is already mixed, this means Water and Foam, no need for mixing onsite. Maintenance personal should open the Pre-Mix bucket and fill the Enforcer unit full of the Pre-Mix solution. - Page 17 Storage and Protection 5-8. a. The Enforcer 30 does not have any special storage requirements if stored inside. b. A protective cover is recommended and should be used if the equipment is stored outside as this will reduce sun ray damage to hoses and gauges.
Need help?
Do you have a question about the 30 and is the answer not in the manual?
Questions and answers