Summary of Contents for ENFORCER 30
- Page 1 Operation and Maintenance Manual Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 1 Copyright 2020...
-
Page 2: Table Of Contents
- Training Chapter 5 Page - Maintenance - Servicing and Maintenance Activities 12-16 - Troubleshooting 16-17 Chapter 6 Page - Pictures 18-20 Chapter 1 Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 2 Copyright 2020... - Page 3 If the product has been altered, modified or repaired in any way, or if the failure is the result of misuse, abuse or misapplication without the prior consent of Enforcer One, LLC, this warranty shall be void and Enforcer One, LLC shall have no obligation to repair or replace the failed product.
- Page 4 MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. No person or entity is authorized to bind Enforcer One, LLC to any other warranty obligation or liability to distributer, purchaser or any third party for any loss of profits, economic loss, indirect, incidental, punitive, special or consequential damages whatsoever and howsoever caused.
- Page 5 DO NOT attempt to use this or any Enforcer One, LLC product(s) if you are tired, injured or under the influence of drugs, medication or alcohol. keep children and bystanders away from the area where Enforcer One, LLC product(s) are in-use.
-
Page 6: System Description
Enforcer 30 produces air aspirated foam providing a thick vapor sealing blanket that will inhibit re-ignition. The Enforcer 30 will produce up to 300 gallons of finished foam with discharge duration of up to 2 ½ minutes. The system can be easily recharged by the end user. -
Page 7: Operating Instructions
Initial Setup 3-1. The Enforcer 30 comes fully assembled. The 30 gallon Premix Tank and Compressed Air Cylinder must be filled prior to use. The proper FIREBULL® Fluorine Free Foam product should be selected based on operational ambient temperatures and type of anticipated fires before putting the unit into service. -
Page 8: Preventative Maintenance Checks And Services
Disconnect fill tower Cap check liquid level. b. Fill up the Premix Tank if low. _______ 4. Check the tire condition. Note any other Problems: Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 8 Copyright 2020... - Page 9 1. Close the Nozzle Valve. 2. Close the Air Cylinder Valve. 3. Open Nozzle valve to depressurize the system or open Pressure Relief Valve. 4. Secure discharge hose. Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 9 Copyright 2020...
-
Page 10: Training
Chapter 4 Training Training Program 4-1. a. Training on the Enforcer 30 should be conducted or reviewed annually for all operators b. Maintenance personnel should complete initial training and refresher training as required c. Trainers should be thoroughly familiar with the system, fire behavior, hazard identification, and basic firefighting techniques d. -
Page 11: Maintenance
Maintenance personnel should contact EnforcerOne whenever any problem arises that cannot be solved using the information in this manual or when unusual situations are encountered or expected. Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 11 Copyright 2020... -
Page 12: Servicing And Maintenance Activities
Enforcer 30 Maintenance Log Preventative Maintenance Checks and Services (PMCS) Refer to Chapter 5 – Maintenance for specific activities Maintenance Date Performed By Notes/Comments Activity Completed Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 12 Copyright 2020... - Page 13 Visual Inspection Air Regulator Every 2 years Inspection Air Cylinder Every 5 Years Hydrostatic Test Premix Cylinder Every 5 Years and Discharge Hose Hydrostatic Test Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 13 Copyright 2020...
- Page 14 Unscheduled Maintenance Maintenance Activity Date Performed Comments/Notes Completed Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 14 Copyright 2020...
- Page 15 9. Important Note: The Premix Tank Manifold should be tightened by hand. Do not use any wrenches or Teflon tape or thread sealant on any of the Premix tank fittings. Enforcer One, LLC FIREBULL® is a registered trademark of Enforcer One, LLC Page 15 Copyright 2020...
-
Page 16: Troubleshooting
Fill the Premix Tank with FIREBULL® Fluorine Free Foam Freeze Protected Premix solution whenever temperatures are below 32 degrees Fahrenheit. FIREBULL® Fluorine Free Foam is a solution made by Enforcer One, LLC. The Pre-Mix solution is already mixed, this means Water and Foam, no need for mixing onsite. Maintenance personal should open the Pre-Mix bucket and fill the Enforcer unit full of the Pre-Mix solution. - Page 17 Storage and Protection 5-12. a. The Enforcer 30 does not have any special storage requirements if stored inside. b. A protective cover is recommended and should be used if the equipment is stored outside as this will reduce sun damage to hoses and gauges.
Need help?
Do you have a question about the 30 and is the answer not in the manual?
Questions and answers