Table of Contents
Advertisement
CTN_ALT BOM#
48PFH5500/88
48PFH5500/88
48PFK5500/12
48PFH5500/88
48PFT5500/12
48PFH5500/88
50PUK6400/12
50PUK6400/12
50PUH6400/88
50PUH6400/88
50PUT6400/12
50PUT6400/12
50PUT6400/60
50PUT6400/60
50PFH6510/88
50PFK6510/12
50PFT6510/12
50PFT6510/60
50PFK6540/12
50PFH6550/88
50PFK6550/12
50PFT6550/12
50PFK6560/12
50PFK6580/12
55PFH5500/88
55PFH5500/88
55PFK5500/12
55PFK5500/12
55PFT5500/12
55PFT5500/12
55PUH6400/88
55PUK6400/12
55PUT6400/12
55PFH6510/88
55PFK6510/12
55PFT6510/12
55PFT6510/60
55PFK6540/12
55PFH6550/88
55PFK6550/12
55PFT6550/12
55PFK6560/12
55PFK6580/12
65PFH6520/88
65PFK6520/12
65PFT6520/12
65PFT6520/60
6.5
Reset of Repaired SSB
A very important issue towards a repaired SSB from a Service
repair shop (SSB repair on component level) implies the reset
of the NVM on the SSB.
A repaired SSB in Service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool or use the "NVM editor" and "Dealer options"
items in SAM (do not forget to "store").
After a repaired SSB has been mounted in the set (set repair
on board level), the type number (CTN) and production code of
the TV has to be set according to the type plate of the set. For
this, you can use the NVM editor in SAM. The loading of the
CTN and production code can also be done via ComPair
(Model number programming).
Panel Type
Display Code
TPT480H2-HWU23.K
214
TPT480LS-HN08.S
032
TPT480H2-HWU23.K
214
TPT480LS-HN08.S
032
TPT480H2-HWU23.K
214
TPT480LS-HN08.S
032
TPT500DK-QS1 SC1H
232
TPT500UK-DJ2QS5.N SM1A 036
TPT500DK-QS1 SC1H
232
TPT500UK-DJ2QS5.N SM1A 036
TPT500DK-QS1 SC1H
232
TPT500UK-DJ2QS5.N SM1A 036
TPT500DK-QS1 SC1H
232
TPT500UK-DJ2QS5.N SM1A 036
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT500J1-HVN08.A
218
TPT550J1-DUYSHA.G S1A
216
TPT550J1-DUYSHA.G S1D
033
TPT550J1-DUYSHA.G S1A
216
TPT550J1-DUYSHA.G S1D
033
TPT550J1-DUYSHA.G S1A
216
TPT550J1-DUYSHA.G S1D
033
TPT550J1-QVN03.U
233
TPT550J1-QVN03.U
233
TPT550J1-QVN03.U
233
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
TPT550J1-HVN06.U
219
V650HP1-LS6 E8
220
V650HP1-LS6 E8
220
V650HP1-LS6 E8
220
V650HP1-LS6 E8
220
Alignments
In case of a display replacement, reset the "Operation hours
display" to "0", or to the operation hours of the replacement
display.
Remark:
- After the NVM has been replaced, go to SAM and scroll to the
<Reload MAC address> (see figure 1*).
- Select the item and press <OK> on the RC.
6.5.1
Reset of Repaired SSB
Instruction
After NVM replacement, reload MAC address via SAM
menu.This ensures the correct MAC address to be available in
CSM for future repair actions.
Way of working:
•
After the NVM has been replaced, go to SAM and scroll to
the <Reload MAC address> .
•
Select the item and press <OK> on the RC.
Notes:
•
Only applicable to all related models that are "Smart TV
level 0"enabled (only YouTube access). For models
without internet connection feature, no action is needed.
•
HDCP keys are located in the NVM. If you are loading NVM
with the ComPair tool, there is warning message displayed.
New NVM EEPROMs are shipped with pre-loaded HDCP keys.
6.5.2
SSB Identification
SSB's of this chassis are identified by a "715" code on the SSB.
715Axxxx-Nnn-MMM-OOOO
•
715 main category, Printed Wiring Board
•
Axxxx sub category, sequential coding number
•
Nnn Version code
•
N Development number
•
nn Production number
•
MMM Mounting variation code
•
OOOO Optional variation code
Make sure when replacing an SSB the SSB identification codes
match the replacement panel.
6.6
Cable position numbers
In this chassis, the cable position numbers can be defined via
the rule that the number is always starting with an "E" followed
by the connector number of the current sourcing board. The
order is always seen from where the power initiates from. So
from PSU to SSB, from SSB to IR/LED panel, from IR/LED
panel to keyboard control panel. For example, a cable from the
PSU connector CN902 to the SSB connector CN701, will have
the position number ECN902.
back to
div.table
QM15.2E LA
6.
EN 41
2015-Sep-30
Advertisement
Table of Contents
