Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Horizon Signal SQ2-T
Summary of Contents for Horizon Signal SQ2-T
- Page 1 SIGNAL TECHNOLOGIES SQ2-T with Multi-Signal 2.0 USER MANUAL 2018...
- Page 3 Important Information This operating manual contains important safety information! Please read carefully and understand all of the in- formation before operating equipment. Save this manual for future use. The owner and/or user of this equipment must have an understanding of the manufacturer’s operating instructions and warnings before using the portable traffic signal system.
- Page 5 Fax: (610) 743-5188 www.horizonsignal.com At Horizon Signal Technologies, we are dedicated to providing unmatched customer service and support. We maintain a 24-hour technical support service center available at no charge to individuals, companies and agencies using our products. To contact our Technical Support Group: 1.
-
Page 6: Table Of Contents
CONTENTS 1) SQ2-T DEPLOYMENT SQ2-T Setup Procedures Photo Guide 2) SQ2-T PROGRAMMING Multi-Signal 2.0 Controller PTS Programmer The Home Screen Assigning Controller Identities Addressing Radios Main Menu Basic Programming Special Programming Edit a Program Download, Upload, Delete System Options System Mode Compatibility Operation 3) FIGURES &... - Page 7 SQ2-T DEPLOYMENT...
-
Page 8: Sq2-T Setup Procedures
1. Position the SQ2-T trailer for deployment. 2. Lower all stabilizer jacks and level the trailer. 3. Use hand crank to raise the signal to the deployed position. 4. Power the system on. 5. Repeat all steps for each SQ2-T trailer in the system. - Page 9 SQ2-T PROGRAMMING...
-
Page 10: Multi-Signal 2.0 Controller
System Features ® The Horizon Signal system is capable of three communication types: • Radio - Wireless communication between all controllers in the system. • Cable - Wired communication between all controllers in the system. • Quartz - Synchronized timing of all controllers in the system via quartz clocks. Controllers do not communicate in this mode. -
Page 11: Pts Programmer
PTS Programmer The PTS Programmer acts as a mechanism to enter programming data into the signal controllers. It also coordinates and synchronizes the signal controllers within a signal system. The Programmer gets plugged into the face of the Controller via the 7-pin Hirschmann plug. Enter / Advance to next menu / Choose Mode Returnto Home Screen / Go back / Move signal selector Acess the Main Menu... -
Page 12: Assigning Controller Identities
Assigning Controller Identities Before a program can be entered, all of the controllers in the system must be communicating. To accomplish this, each controller is given an identity. Additionally, when using wireless communication, each radio must be assigned a “Master” or “Slave”... -
Page 13: Main Menu
Basic Programming Programs can be edited or changed at any time while the Horizon Signal system is running. By plugging in the Programmer, the user can create new programs without any effect on the current program. A new program that is created will be loaded during the next Red Clearance time, and will be undetectable by motorists. - Page 14 3. Set the green times for Phase 1. The first number on the screen is the base PROGRAM 1 / C1 green. This is the minimum amount of green time a given phase will allow without detection. The second number is the extension time. The extension will Green: 10 s Extension:...
-
Page 15: Special Programming
Special Programming Special Programs allow for more control than basic programs, allowing the user to adjust all settings and create custom signal groups for more advanced aplications. To create a special program, choose Programming from the Main Menu, and select “SPECIAL.” SPECIAL 1. - Page 16 5. Set the number of programs. Up to 20 different programs can be created, each SPECIAL with differnt green times for different times of day / day of week. If you do not wish to change timings based on time or day, keep this value at 1. Amount of programs 6.
-
Page 17: Edit A Program
9. Enter program parameters. PARAMETER Max Red: If a signal has rested in red for this amount of time, a call will be Max. red: -- s placed to force a cycle on that phase. Min. red: Min Red: Minimum red time between green indications on the same phase. Min. -
Page 18: Download, Upload, Delete
Download, Upload, or Delete a Program Download Program Download Program The “Download Program” function on the Main Menu allows you to pull the currently run- ning program and save it into the Programmer’s memory if it had not already been saved during creation. -
Page 19: System Options
If the password is forgotten, please contact Horizon Signal at 800-852-8796. NOTE: If any of these settings are changed, they will not take effect until a new program is loaded. -
Page 20: System Mode
System Mode The mode function of the micro-terminal is used to change between signal operation modes. This menu can also be accessed by simply pressing “E” from the home screen. Once inside this menu, the user can scroll through the various operational modes by using the Up and Down Arrow buttons and pressing “E”... -
Page 21: Compatibility Operation
2. Power MS 2.0 controller back ON. 3. To use MS 2.0 Programmer: Compatibility 4.0.31 Plug in the Programmer. When the Horizon Signal Logo Screen appears, press R and E at the same time. The title heading of the screen will change horizon to say “Compatibility”... - Page 23 FIGURES AND DIAGRAMS...
-
Page 24: Dimensions
SQ2 Deployed Dimensions... -
Page 25: Transport Position
SQ2 Stowed Dimensions... -
Page 26: Circuit Board Diagram
SQ3TS Circuit Board Diagram... -
Page 28: Terminal Block
Terminal Block All connections to the Multi-Signal 2.0 controller are made via the Terminal Block located inside the SQ3TS cabinet. See the diagram below for details. -
Page 29: Molded Trailer Plug
Molded Trailer Plug & Vehicle Connector Below is the Wiring Diagram for the 7-Pole Molded Standard Trailer RV Cord used on the SQ3TS trailers. The cords have encapsulated terminals and wires to form a single weather-tight, noncorrosive assembly. This feature keeps the moisture out and allows for a more secure connection. - Page 31 MAINTENANCE...
-
Page 32: Battery Maintenance
It is important to note that in colder climates solar collection alone may not be sufficient to maintain optimum battery voltage. If battery voltage drops, the Horizon Signal system can be charged using an external power source, such as a generator. The battery charger can be connected to an 110v power source by using the power adapter located underneat the front of the trailer. -
Page 33: Limited Warranty
HORIZON SIGNAL TECHNOLOGIES LIMITED WARRANTY Horizon Signal Technologies, hereinafter referred to as HST, warrants New or Used HST Equipment and accessories to be free from defects in material and workmanship for a period of two years from the date of receipt of goods, subject to the conditions and restrictions contained herein. - Page 34 horizon SIGNAL TECHNOLOGIES 5 CORPORATE BLVD READING, PA 19608 (800) 852-8796 www.horizonsignal.com...
Need help?
Do you have a question about the SQ2-T and is the answer not in the manual?
Questions and answers