Table of Contents
Related Manuals for gagalight RGB6000
Summary of Contents for gagalight RGB6000
- Page 1 User Manual RGB6000 laser light Introduction Thank you for purchasing our product. To ensure proper operation, please read this manual carefully before using the product. After reading it, keep it in a safe place for future reference. 第 1 页...
-
Page 2: General Information
General Information The following chapters explain important information about lasers in general, basic laser safety and some tips about how to use this device correctly. Please spend some time reading these information as some of them are critical for safe and efficient operation of this laser display system. 第... - Page 3 Caution This laser entertainment system is rated as a Class IV laser product and manufactured in accordance to EN 60825-1:2007. Avoid eye or skin exposure to direct or scattered radiation. Wear protective goggles of suitable optical density if necessary. If the laser is operated in a situation where health or property injury may occur the operation must be stopped immediately.
-
Page 4: What Is A Laser And How Does It Work
What is a laser and how does it work? What is a LASER? The laser is a bunch of energy waves (streams of photons called radiation) with the same amplitude and faze that are flowing in the same direction; meaning they are coherent – they stick together and form a laser beam. -
Page 5: Laser Safety First
Laser Safety First! Before proceeding any further, please read the following safety page very carefully. It could help you avoid dangerous and hazardous situations which could lead to serious injury or property damage. Any laser system classified as a Class 4 laser must be used with caution. If you are not an experienced laser operator we would strongly recommend that you attend a laser display safety course as soon as possible, and ideally before this laser system is used in pubic areas. -
Page 6: Installation Of The System
Installation of the System The manufacturer is not liable for damages or a injury caused by improper installation of the system. The installation should be carried by a qualified installer who should follow the Laser Please follow these rules during the installation: Safety Regulations of respective country. - Page 7 Scanning System The product warranty does not cover the damages to the scanning system caused by improper use of the scanning system or by incorrect programming. Therefore it is essential to understand how the scanning works and where are the limits of it. In this manual we will explain only the basics of it but it is the responsibility of every user to educate themselves so they can avoid damage being caused to the scanning system and costly repairs.
- Page 8 So we need to display 300 points 35 times per second = 10.500 pps. This means that we could display 3of these stars beside each other within one single laser effect and that it would be quite close to the scanner limit (3 × 10.500 = 31.500pps). This however applies than 8 degrees on both axes! If we start to increase the size of the projection (scanning angle) it is necessary to either lower the number of points within the effect or drop down the scan-rate in the control software (FPS) to a safe level –...
- Page 9 Connection Diagram Please check that all the signal and power leads are correctly installed and that the safety keys are inserted in all necessary positions. Basic connection diagram Both E-STOP Remote safety key and laser system safety key must be inserted and switched to ON position in order to disable the interlock.
- Page 10 Power Connections Method Please connect power as following ： L（live wire ）=brown wire E （earth wire） =yellow/green double color wire N （null line ）=blue wire When connecting,ensure that the voltage and frequency of power supply match the power requirement of the product. This product is Class 1 protection equipment.The yellow-green double colors wire must be earthed by qualified personnel.
- Page 11 This product accepts digital control signals in protocol DMX512(1990).The amount of lighting fixtures connected in parallel is no more than 32.Connect the DMX controller's Output to the first lighting fixture's Input cable with a 2 core XLR signal cable(Shown as above ),connect the first lighting fixture's Output cable to the second lighting fixture's Input cable and connect the rest light fixtures in the same way.Eventually,connect the last lighting fixture's Output cable to a DMX terminator Under DMX-512 signal control mode,the last lighting fixture's DMX Output must be...
-
Page 12: Rear View
Rear View IN / OUT: connect software AC IN/OUT: AC input 110-240v 50/60Hz DMX-ILDA: DMX change to ILDA FUSE: fuse Power: power switch on/off X INVERT Y : X / Y invert Laser Power Control: Each color power adjust DMX IN / OUT: connect DMX DMX/Linking: Dip switch 第... -
Page 13: Product Technical Parameters
Product technical parameters 1.Voltage:AC90~240V 50~60HZ±10% 2.Power consumption:120W 3.Laser source: diode. 4.Laser power /wavelength: 1x2000mW Red(638nm) 1x2000mW Green (520nm ) 1x2000mW Blue (445nm ) 5.Beam size: 4mm at aperture 6.Divergence: <1.5mrad-full angle 6.Colors:RGB full color 7.External Modulation:Analog 100k 8.Scanner system: 40kpps 9.Control signal: ILDA international standard signal 10.Control mode: ILDA Control 13.Cooling system:air cooling... -
Page 14: Dmx Channel Chart
DIP switch: Address 1-10 Pin Function 0,0,0,0,0,0,0,0,0,0 Sound Mode 1,0,0,0,0,0,0,0,0,0 Auto Mode 0,0,1,0,0,0,0,0,0,0 Slave Mode 1,1,0,0,0,0,0,0,0,0 Graphic Mode x,x,x,x,x,x,x,x,x,1 DMX 512 Control DMX Channel Chart : Channel DMX 512 Control Function value 0~49 Music Trigger 0--49 Music trigger 50--99 Auto trigger（Beam） 1.Mode Select 100--149 Auto trigger（Pattern）... - Page 15 Rotation by hand 0--127 Clockwise rotation auto 128--191 8. Rotation Counterclockwise rotation auto 192--255 From small to big 0--85 From big to small 9.Zoom 86--170 Alternately zoom 171--255 10.Pattern size 0: original size; 1:smallest;255:biggest 0--255 11.A hot point 0:disappear; 1:darkest;255:brightest 0--255 Auto gradually drawing1 12.gradually...
-
Page 16: Maintenance
Maintenance To prolong the life of the product, it is very important to do maintenance work. The environment is hash outdoors, or if the product is idle for a long time, damp, smoke or particularly dirty surroundings can cause greater accumulation of dirt on its cover and housing.