VIPAR SPECTRA Timer Control TC1200 User Instructions

USER INSTRUCTIONS
Timer Control Series
8pcs
MODEL: TC1200
For flowering stage: use all channels with 100% brightness.
This light includes IR (Infrared) LEDs which look dim/invisible, they are not faulty LEDs.
Two fans will work while VEG channel on, the rest two fans will work while BLOOM channel on.
The digital display will be turned off so it will not illuminates/emits blue light during light off-working time.
Specifications:
Model: TC1200 HID Replacement:
LED Power: 1200W Vegetative Coverage at 32":
Actual Power Draw: Flowering Coverage at 24":
110V: 530W±3%; 220V: 506W±3%
LED Quantities: 240pcs Epiled/Bridgelux LEDs Use for:
<
Total Harmonic Distortion: Housing Dimensions:
15%
Input Voltage: AC100-240V Item Weight:
Frequency: 50-60Hz Lifespan:
Setting system with Remote
IR look dim
To turn ON/OFF the light.
To increase value.
Switch to other setting.
To setup brightness for
VEG channel.
To setup light's start-working
time.
Step 1. Remove the plastic separator from the battery.
Step 2. Press to turn on the light.
Step 3. Press to setup brightness for VEG channel. Using
VEG
1000W HPS/MH
desired brightness. Press
4.5x4.5ft
3.5x3.5ft Step 4. Press , repeat step 3 to setup brightness for BLOOM channel.
BLOOM
all stages grow and flowering
Step 5. Press to setup current time of day, the hour will flash. Using
25.4 x 16.5 x 3 inches CLOCK
64.5 x 42 x 7.5 cm
select the desired hour. Press
23 lbs Using and
≥ 100,000 hours about 3 seconds and the programmed time will be automatically saved.
www.viparspectra.com
To preview start-working
PREVIEW
and off-working time.
To save settings.
Switch to other setting.
OK
To decrease value.
To setup brightness for
BLOOM
VEG
BLOOM channel.
To setup current time of day.
To setup light's off-working
ON CLOCK OFF
time.
VIPAR SPECTRA
and
to save settings.
OK
or to save the hour and activate the minutes.
, select the desired minutes. Press to save settings, or wait
OK
02
Step 6. Press
to setup light's start-working time, the hour will flash. Using
ON
, select the desired start-working hour. Press
activate the minutes. Using and
save settings, or wait about 3 seconds and the programmed time will be automatically
saved.
Step 7. Press
, repeat step 6 to setup light's off-working time.
OFF
Step 8. Press to confirm that the system has saved the desired start-working and
PREVIEW
off-working time.
Note: Timer controls both channels on/off together. Cannot turn VEG and BLOOM channel
on/off separately.
Using Suggestions
The following section will help guide you in the process of evaluating the best methods
for each stage of plant growth. Like many other growers, you can use this light throughout
the seeding and flowering stages of your plants life. Remember to properly adjust the height
and brightness of your light according to your plants desired level for optimal growth.
TC1200 Height (above plants' canopy)
3-5 days acclimation period 44" - 48"
Seedlings/ Young vegetative 40" - 44"
Vegetative Stage 32" - 40"
, select the
Flowering Stage 24" - 28"
Adjust the height and brightness accordingly to desired coverage and how well each individual
plants responds as the brightness increases. The key is to always observe your plants and listen
to what they're telling you. If the leaves are pointing hard towards the light, they love it! Give
and ,
them more! If they shy away or appear limp and unhappy, while all other components and
environmental variables are correct, back off with the light! They'll let you know very quickly how
they feel. This is of course... the key to horticulture in general.
and
or to save the hour and
, select the desired minutes. Press to
OK
Using Hours Brightness (VEG/BLOOM)
10 on / 14 off 40 / 15
12 on / 12 off 60 / 30
18 on / 6 off 100 / 60
12 on / 12 off 100 / 100