Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Compac L40P
Summary of Contents for Compac L40P
- Page 1 Version: L40P L80P Date of issue: 17 October 2013 Compac Industries Ltd P O Box 12-417 Penrose Auckland New Zealand Ph 64 9 5792 094 Fax 64 9 5790 635 www.compac.co.nz G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 1 of 16...
-
Page 2: Table Of Contents
Standalone Operation ......................12 Spare Fuses ........................12 Precautions if Using Generator Power ..................12 Error Messages ........................12 L40P L80P Spare Parts ......................14 Product Details ........................15 Contact Details ........................15 Notes ..........................15 Revision History ........................16 G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc... -
Page 3: Conditions Of Use
Unless otherwise noted, references to brand names, product names, or trademarks constitute the intellectual property of the owner thereof. Subject to your right to use the unit, Compac does not convey any right, title, or interest in its intellectual property, including and without limitation, its patents, copyrights, and know-how. -
Page 4: Footprint
Nozzle 8 Mounting Rear of Unit Holder Holes Ø20 Front of Unit Standard 3 bolt Outlet triangular flange Footprint Plan View L40P L80P G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 4 of 16... -
Page 5: Static Electricity Precautions
This is not a recommended alternative to wearing an anti-static wrist strap. Note: Compac Industries Limited reserves the right to refuse to accept any circuit boards returned, if proper anti-static precautions have not been taken. -
Page 6: Comms Dip-Switch Settings
(Dipswitch SW3) 1-ON 2-OFF 3-ON 4-OFF These are factory set to the standard setting unless ordered otherwise.eg Gilbarco. Gilbarco Pump comms Setting (Special software and interface board required) 1-OFF 2-ON 3-OFF 4-ON G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 6 of 16... -
Page 7: Triac Dip-Switches
These switches are set in the factory and should not be changed. If they are accidentally changed these are the correct settings for Laser Pump applications. Note: They are 3 position switches Pump (Motor triac fitted) Centre G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 7 of 16... -
Page 8: Electrical Connections
Note: Comms cable is not intrinsically safe. Note: Pump comm’s connect to pump controller such as DCA, Communicator Controller etc. (option). When replacing the lid of the flameproof enclosure, ensure the sealing O ring is in place. G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 8 of 16... -
Page 9: Dispensing Hoses And Nozzles
Configuration Code 10.1 The configuration code has been set at Compac and should not be changed In the event of it being lost and having to be re-entered the configuration is written on the yellow label on the C4000 processor board cover. -
Page 10: K-Factor Switch Settings
J15: Not used Side A J4: Input from KG Meter J10: Totes J16: Not used Side B J5 : Not Used J11: Buzzer J17 Backlighting G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc J6 Not used J12 Nozzle Switches Page 10 of 16... -
Page 11: Calibration (K-Factor)
Existing Factor 10.00 Existing Factor Change the existing 'K' Factor to this new value. Sealing the K-Factor switch 11.2 After calibration the K-factor switch should be sealed as shown G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 11 of 16... -
Page 12: Standalone Operation
Err 9 Faulty or disconnected meter encoder. Check that encoder is plugged in. Replace encoder PCB on meter Err 10 Configuration Lost Reconfigure C4000 refer to C4000 manual G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 12 of 16... - Page 13 Err 12 C4000 memory failure. Change memory IC. F-AD-DS1225 (not applicable to Futra) Display error Check display cable for loose wires/crimps Replace display PCB G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 13 of 16...
-
Page 14: L40P L80P Spare Parts
3/4 HP Electric Motor F-MOTOR-230-550W Pump Unit (incl inlet and outlet gaskets) F-PUMP-ZYB-50-40 (for 40lpm only) F-PUMP-ZYB-50 (for 80lpm only) C4000 Power Supply (does not include box) F-CP-C4PWR-ASSEM Motor Triac F-AT-BTA40-RD91 G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 14 of 16... -
Page 15: Product Details
Phone E-mail Address 1 Address 2 Notes Manufacturer Contact The Compac Laser Dispenser is designed and Details manufactured by: Compac Industries Limited 52 Walls Road, Penrose, Auckland 1061, New Zealand P.O. Box 12-417, Penrose, Auckland 1641, New Zealand Phone: + 64 9 579 2094 Fax: + 64 9 579 0635 www.compac.co.nz... -
Page 16: Revision History
Revision History Previous revision date Summary of changes 20/05/2010 Added Conditions of Use and 12/06/2012 Updated pipe installation, generator power & hose breakaway instructions. 19/06/2013 Updated wiring info & spare parts G:\Masters\Installation Sheets\Laser\L40P L80P Installation Sheet.doc Page 16 of 16...
Need help?
Do you have a question about the L40P and is the answer not in the manual?
Questions and answers