Advertisement
Intelligent Controller LNL-X2210 with Paired Reader
Interface for One Physical Barrier Quick Reference
General
The LNL-X2210 intelligent controller provides decision making, event reporting and database storage for the Lenel
hardware platform. Two reader interfaces configured as paired or alternate readers provide control for one physical
barrier.
Host communication is via the on-board 10-BaseT/100Base-TX Ethernet port.
Note:
For UL compliance, the Power Sourcing Equipment (PSE) such as a PoE or PoE+ enabled network
switch and/or PoE or PoE+ power injectors must be UL Listed under UL 294.
Reader port 1 can accommodate a reader that utilizes TTL (D1/D0, Clock/Data), F/2F, or 2-wire RS-485 device
signaling (for example an OSDP reader), also provides tri-state LED control, and buzzer control (one wire LED mode
only). This port can also utilize multiple 2-wire RS-485 multi-dropped devices, such as up to two OSDP readers or up
to eight remote serial I/O devices.
Reader port 2 can accommodate a reader that utilizes TTL (D1/D0, Clock/Data), or F/2F signaling, also provides tri-
state LED control, and buzzer control (one wire LED mode only). Two Form-C contact relay outputs may be used for
door strike control or alarm signaling. The relay contacts are rated at 2 A @ 30 VDC, dry contact configuration. Two
inputs are provided that may be used for monitoring the door contact, exit push button or alarm contact. Input circuits
can be configured as unsupervised or supervised. The LNL-X2210 requires Power over Ethernet (PoE or PoE+) or
12 VDC for power. The LNL-X2210 may be mounted in a 3-gang switch box; a mounting plate is supplied with the
unit, or may be mounted in an enclosure; the supplied mounting plate has mounting holes that match the LNL-1300
mounting footprint.
LNL-X2210 Hardware
1
J7: Tamper
switch
commection
J7
J5: Micro
USB jack
J8: microSD CARD
(back side)
Ø .125 [Ø3.175]
6 PL
© 2021 Carrier. All Rights Reserved. LenelS2 is a part of Carrier.
For detailed information, refer to the hardware documentation for the host
application.
5.40 [137.16]
2.55 [64.77]
1
1
TB1
TB2
TB3
7
6
5
4
3
2
1
3
4
2 1
V
ON
S1
DIP switches
Status LEDs
J3: PoE/12 VDC power selector jumper
2.55 [64.77]
1
1
J3
12V
TB4
TB5
PoE
K1
K2
Earth GND
1
QR50L-1036E
.15 [3.81]
J6: Ethernet
connector
.20 [5.08]
—
revision 4.004
Advertisement
Table of Contents
Related Manuals for LenelS2 LNL-X2210
Summary of Contents for LenelS2 LNL-X2210
- Page 1 The LNL-X2210 requires Power over Ethernet (PoE or PoE+) or 12 VDC for power. The LNL-X2210 may be mounted in a 3-gang switch box; a mounting plate is supplied with the unit, or may be mounted in an enclosure; the supplied mounting plate has mounting holes that match the LNL-1300 mounting footprint.
- Page 2 Jumpers Jumper Description Factory Use Only LNL-X2210 powered from the Ethernet connection LNL-X2210 powered from an local 12 VDC power source connected to TB4-3 (VIN), TB4-4 (GND) Factory Use Only Micro USB port (2.0) 10-Base-T/100Base-TX Ethernet Connection Cabinet Tamper Switch Input: short = tamper secure microSD Card —...
-
Page 3: Dip Switches
Apply power to the LNL-X2210 board. LED 1 on for about 15 seconds while LNL-X2210 boots up. After the LNL-X2210 boots up, watch for LEDs 1 & 2 and 3 & 4 to alternately flash at a 0.5 second rate. -
Page 4: Input Power
Intelligent Controller LNL-X2210 Quick Reference The LNL-X2210 board will complete its initialization in 2 seconds after LEDs 1 & 4 stop flashing. Input Power The LNL-X2210 is powered by one of two ways (jumper selected, J3): • Power is supplied via the Ethernet connection using PoE or PoE+ •... - Page 5 NORMALLY OPEN CONTACT * * Inputs on supervised F/2F readers may be unsupervised or supervised (supervised shown). Note: Jumper: Connect D1 and LED on supervised F/2F reader. — QR50L-1036E revision 4.004 © 2021 Carrier. All Rights Reserved. LenelS2 is a part of Carrier.
- Page 6 Custom end of line (EOL) resistances may be configured via the host software. * Grounded and foreign voltage states are not a requirement of UL 294 and therefore not verified by UL. — QR50L-1036E revision 4.004 © 2021 Carrier. All Rights Reserved. LenelS2 is a part of Carrier.
- Page 7 Door lock mechanisms can generate EMF feedback to the relay circuit that can cause damage and premature failure of the relay plus affect the operation of the LNL-X2210. For this reason, it is recommended that either a diode or MOV (metal oxide varistor) be used to protect the relay. Wire should be of sufficient gauge to avoid voltage loss.
-
Page 8: Memory Backup Battery
Upon installation, the user accounts to the web configuration page should be created with secure passwords, and that all DIP switches are in the off position for the normal operating mode. The LNL-X2210 is shipped from the factory with a default login account, which is enabled when DIP 1 is moved from OFF to ON. The default login user name and password will be available for five minutes once enabled. -
Page 9: Specifications
Card Format: microSD or microSDHC; 2GB to 8GB. Host Communication: Ethernet: 10-BaseT/100Base-TX and Micro USB port (2.0) with optional adapter: pluggable model USB2-OTGE100 — QR50L-1036E revision 4.004 © 2021 Carrier. All Rights Reserved. LenelS2 is a part of Carrier. - Page 10 These specifications are subject to change without notice. UL Listed Installations • PoE is only for use with Access control-only installations and not for use with burglar installations. — QR50L-1036E revision 4.004 © 2021 Carrier. All Rights Reserved. LenelS2 is a part of Carrier.
-
Page 11: Firmware Revision
Magnetic switch set: G.R.I. part number: 505 OPTIONAL BLANK COVER W/SCREWS OPTIONAL MAGNETIC TAMPER SWITCH LNL-X2210 WITH INCLUDED MOUNTING PLATE OPTIONAL 3-GANG JUNCTION BOX TO ETHERNET FIELD WIRING NETWORK — QR50L-1036E revision 4.004 © 2021 Carrier. All Rights Reserved. LenelS2 is a part of Carrier. -
Page 12: Regulatory Information
This product is not intended for, nor is rated for operation in life-critical control applications. LenelS2 is not liable under any circumstances for loss or damage caused by or partially caused by the misapplication or malfunction of the product. LenelS2’s liability does not extend beyond the purchase price of the product.