Dell PowerEdge R910 Information Update
Information update
Hide thumbs
Also See for PowerEdge R910:
- Information update (92 pages) ,
- Technical manual (63 pages) ,
- Getting started with (63 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dell PowerEdge R910
Summary of Contents for Dell PowerEdge R910
- Page 1 Dell PowerEdge R910 Systems Information Update...
-
Page 2: Notes, Cautions, And Warnings
____________________ © 2010–2012 Dell Inc. Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc. ® Intel is a registered trademark of Intel Corporation in the U.S. and other countries. Microsoft ®... - Page 3 Power Supply Removal Updates The I/O riser with 10G network port requires a minimum of two power supplies to provide standby power to the system. If you remove AC power cables from the system while DC power is on, the system may momentarily operate below the minimum power supply requirement.
-
Page 4: System Memory Update
System Memory Update The system supports 32 GB quad-rank RDIMMs for a total of up to 2 TB. Table 1 shows the memory configurations available with 32 GB RDIMMs in a four-processor system. Table 1. Memory Configuration With 32 GB RDIMMs per Processor Memory Total Memory Mode... -
Page 5: Flash Memory
Flash Memory The VFlash media provided by Dell is not partitioned to support the iDRAC6 Enterprise virtual flash feature. When you use the virtual flash feature for the first time, you are prompted to format the media using the iDRAC GUI. -
Page 6: Nic Teaming
For more information on supported adapters, see the Dell PowerEdge R910 Hardware Owner's Manual at support.dell.com/manuals. Dell Update Package Information During the Dell Update Package (DUP) installation process, you may see messages related to the following: • Request for system reboot before the DUP installation is complete •... - Page 7 Dell PERC H800 Storage Adapter Slot Limitation (With PERC H700i as the Internal Storage Controller) The system supports up to two PERC H800 adapters. There is no slot limitation when only one H800 adapter is installed. However, when you install two H800 adapters in a system with a PERC H700i internal storage adapter, one of the H800 adapters must be installed in slot 7 (x16 Gen 2 slot).
-
Page 8: Hardware Owner's Manual Updates
Hardware Owner’s Manual Updates System Board Jumper Settings Update This update supersedes the information provided in the Hardware Owner's Manual at support.dell.com/manuals. To locate the system board jumpers, see Figure 1. Table 3. System Board Jumper Settings Jumper Setting PSWD_EN... - Page 9 Figure 1. System Board Jumpers Information Update...
- Page 10 BIOS Setup Options Default Settings Update Table 4. Default Settings for BIOS Setup Options Screen Memory Settings Power Management Integrated Devices SATA Settings Power Supply Redundancy Mode (With a 10 Gb I/O Card) For a redundant system configuration with a 10 Gb I/O card and four power supplies, the redundancy mode is 2+1.
-
Page 11: System Memory
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. - Page 12 Repeat step 5 through step 7 of this procedure to install the remaining memory modules. See Table 3-1 and Table 3-2 in the Hardware Owner’s Manual. 8 Press the four tabs and close the memory module cover. See Figure 3. 9 Install the memory risers.
- Page 13 Figure 2. Installing and Removing a Memory Module release tabs (2) memory riser card guide handle release button memory-riser connector Information Update...
- Page 14 You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
- Page 15 Figure 3. Removing and Installing the Memory Module Cover release tab tabs (4) 7 Install the memory risers. See "Installing a Memory Riser" in the Hardware Owner’s Manual. 8 Close the system. See "Closing the System" in the Hardware Owner’s Manual.
- Page 16 Information Update...