Advertisement
7.
WIRING DIAGRAM
Fig.10
8. TROUBLE SHOOTING
Problem
Heater fires, but shuts down after a
short period of time.
Heater will not operate, or motor
runs for short time.
fan does not operate when heater
is plugged in and Power switch is
in the 'HI / Lo' position.
Heater does not turn on and the
lamp is not lit.
Poor combustion and / or soot
production.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Possible Cause
1. Dirty fuel filter.
2. nozzle Dirty.
3. Photocell Dirty.
4. Photocell not installed properly.
5. Photocell Defective.
6. Improper electrical connection between circuit
Board and Photocell.
7. cooling fan is obstructed.
1. no fuel in fuel tank.
2. corroded spark Plug or incorrect plug gap.
3. Dirty fuel filter.
4. Dirty nozzle.
5. Moisture in fuel/fuel tank.
6. Improper electrical connection between
transformer and circuit Board.
7. transformer Wires not connected to spark Plug.
8. Defective transformer.
1. Broken electrical connection between circuit Board
and motor.
2. not enough amps available to power heater.
1. temperature limit sensor has overheated.
2. no electrical power.
3. fuse break down.
4. Improper electrical connection between
temperature Limit sensor and circuit Board.
1. Incorrect pump pressure.
2. Poor fuel quality.
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and
packaging should be sorted, taken to a recycle centre and disposed of in a manner which is compatible
When the product is no longer required, it must be disposed of in an environmentally protective way.
contact your local solid waste authority for recycling information.
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park,
Bury st. Edmunds, suffolk,
IP32 7Ar
Original Language Version
WARNING! This heater is not suitable for use with
Bio-Diesel; use of Bio-Diesel will damage
the filter and seals.
Damage caused by use of Bio-Diesel will
not be covered by warranty.
1. clean/replace fuel filter.
2. clean/replace nozzle.
3. clean/replace Photocell.
4. Adjust Photocell position.
5. replace Photocell.
6. check wiring connections
(see Wiring Diagram, fig.10).
7. check to make sure cooling fan is not obstructed.
1. fill tank with fresh fuel.
2. clean/replace spark Plug.
3. clean/replace fuel filter.
4. clean/replace nozzle.
5. Rinse out fuel tank and fill with clean fresh fuel.
6. Inspect all electrical connections.
(see Wiring Diagram, fig.10).
7. re-attach transformer wires to spark Plug.
8. replace transformer.
1. Inspect all electrical connections.
(see Wiring Diagram, fig.10).
2. use a new extension cord or try another
electrical socket.
1. Push Power switch to 'off' and allow heater to
cool for 5 minutes.
Push Power switch to 'HI / Lo'.
2. check power cord and extension cord to ensure
proper connection. test power supply.
3. check/replace fuse.
4. Inspect all electrical connections.
(see Wiring Diagram, fig.10).
1. Ensure pump pressure is adjusted correctly.
2. Ensure fuel is not old or contaminated.
Environmental Protection.
with the environment.
01284 757500
01284 703534
Solution
www.sealey.co.uk
Web
sales@sealey.co.uk
email
Ir37.V2
Issue: 4 - 19/04/11
Advertisement
