Toshiba DR20KB Owner's Manual page 66

E7TE0BD_EN.book Page 66 Friday, March 5, 2010 5:08 PM
Video
Setup General Setting Video
A TV Aspect
B Select Video
C
Video Out
A TV Aspect (Default: 16:9 Wide)
Use this feature to adjust the aspect ratio of the video
source which is different from your TV's ratio to fit your TV
monitor without distorting the picture.
TV Aspect
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
If you have a standard TV:
Select "4:3 Letter Box", so that black bars appear on the
top and bottom of the TV screen when playing back a
wide-screen picture. Select "4:3 Pan & Scan" for a full
height picture with both sides trimmed when playing back
wide-screen picture.
If you have a widescreen TV:
Select "16:9 Wide".
For B, refer to page 37.
C Video Out (Default: SCART (RGB))
This unit is compatible with the Progressive Scan System.
The feature provides you with the higher definition images
than the traditional output system does. You can enjoy
Progressive Scan image by using HDMI OUT or
COMPONENT VIDEO OUTPUT. To utilise the
Progressive Scan system through the COMPONENT
VIDEO OUTPUT, you must set video output mode in
"Setup" menu by following the steps. "SCART (RGB)" is
selected as the default.
• When you set "Video Out" setting, you need a Scart
cable or an HDMI cable to output from this unit with
component video cable.
1
Select the desired setting using [K L], then
press [ENTER OK].
Video Out
SCART (RGB)
Component (Progressive)
Component (Interlace)
• If your TV is compatible with progressive scanning
(576p/480p), connect the TV to the COMPONENT
VIDEO OUTPUT jacks of this unit and select
"Component (Progressive)" and set your TV to the
progressive scan mode.
• If your TV is not compatible with progressive scan,
select "Component (Interlace)" for component
connection, or select "SCART (RGB)" for Scart cable
connection.
• Refer to page 16 for more details.
Only if you select the "Component (Progressive)",
2
proceed to step . If you select "Component (Interlace)"
or "SCART (RGB)", your setting is activated.
2
Select "Yes" using [0 1], then press
[ENTER OK].
Final confirmation window will appear.
66
EN
3
Select "Yes" using [K L], then press
[ENTER OK] within 15 seconds.
Confirm again to use progressive scan.
If picture is good, select "Yes".
Yes
No
Your setting is activated.
Note
• When changing "Video Out" setting ("SCART (RGB)",
"Component (Progressive)" or "Component (Interlace)"),
connect to the corresponding jack on the TV. If the
setting is changed, for example, to "SCART (RGB)"
while the COMPONENT VIDEO OUTPUT jacks are
used to connect to the TV, a distorted video signal may
be output.
Clock
Setup General Setting Clock
A
Clock Setting
B
Auto Clock Setting
Note
• If DVB channels are memorised, "Clock Setting" cannot
be changed.
A Clock Setting
Clock Setting
01 / 01 / 2010 (FRI)
0 : 00
Default date will appear.
1
Enter the date (day / month / year) using
[K L].
Press [1] to move the cursor to the next field. If you
want to go back to the previous field, press [0].
2
Enter the time (hours / minutes) using [K L],
then press [ENTER OK].
The clock will start.
• Although seconds are not displayed, they will be
counted from zero.
Note
• Your clock setting will be lost if either there is a power
failure or the unit is unplugged for more than 30
seconds.
• The clock is not displayed in standby mode because the
unit will return to a new Power Saving mode (ECO) with
the display off.