Related Manuals for ZyXEL Communications ZyXEL Dimension GS-1008
Summary of Contents for ZyXEL Communications ZyXEL Dimension GS-1008
- Page 1 Dimension GS-1008/GS-1016 Gigabit Ethernet Switch User’s Guide Version 1.0 May 2003...
-
Page 2: Copyright
ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. -
Page 3: Zyxel Limited Warranty
Dimension GS-1008/GS-1016 Gigabit Ethernet Switch ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two (2) years from the date of purchase. -
Page 4: Interference Statements And Warnings
Dimension GS-1008/GS-1016 Gigabit Ethernet Switch Interference Statements and Warnings FCC Interference Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operations. - Page 5 Dimension GS-1008 Gigabit Ethernet Switch Certifications Refer to the product page at www.zyxel.com. Interference Statements and Warnings...
-
Page 7: Customer Support
LOCATION WORLDWIDE support@zyxel.com.tw sales@zyxel.com.tw NORTH support@zyxel.com AMERICA sales@zyxel.com SCANDINAVIA support@zyxel.dk sales@zyxel.dk GERMANY support@zyxel.de sales@zyxel.de Customer Support Dimension GS-1008 Gigabit Ethernet Switch Customer Support TELEPHONE/FAX WEB SITE/ FTP SITE +886-3-578-3942 www.zyxel.com www.europe.zyxel.com +886-3-578-2439 ftp.europe.zyxel.com +1-714-632-0882 www.zyxel.com 800-255-4101 +1-714-632-0858 ftp.zyxel.com +45-3955-0700 www.zyxel.dk +45-3955-0707 ftp.zyxel.dk... -
Page 9: Table Of Contents
Preface ... xii Chapter 1 Getting to Know the GS-1008/ GS-1016... 1-1 Features ... 1-1 Package Contents ... 1-2 Backbone Switch Network Application ... 1-2 Chapter 2 Hardware Description and Installation ... 2-1 Desktop Installation ... 2-1 Rack-mounted Installation ... 2-2 Rear Panel ... - Page 10 2.4.4 Front Panel LEDs... 2-6 Chapter 3 Troubleshooting ... 3-1 Introduction... 3-1 3.1.1 PWR LED ... 3-1 3.1.2 LK/ACT or LNK/ACT LED... 3-1 3.1.3 100, 1000 LEDs ... 3-2 3.1.4 FD or FDX/COL LED ... 3-2 Improper Network Cabling and Topology... 3-2 Appendix A Product Specifications...A Index ...C Table of Contents...
- Page 11 Figure 2-1 Attaching Rubber Feet... 2-2 Figure 2-2 Attaching Mounting Brackets and Screws ... 2-3 Figure 2-3 Mounting the Switch to an EIA Standard 19-inch Rack ... 2-3 Figure 2-4 GS-1008 Rear Panel ... 2-4 Figure 2-5 GS-1016 Rear Panel ... 2-4 Figure 2-6 GS-1008 Front Panel ...
-
Page 12: Preface
Congratulations on your purchase of the Dimension GS-1008/GS-1016 Gigabit Ethernet Switch. This preface introduces you to the Dimension GS-1008/GS-1016 Gigabit Ethernet Switch and discusses the organization and conventions of this User’s Guide. It also provides information on other related documentation. About Gigabit Ethernet Gigabit Ethernet is a 1Gbps (1000Mbps) extension of the IEEE 802.3 Ethernet... -
Page 13: Chapter 1 Getting To Know The Gs-1008/ Gs-1016
Ethernet routers, switches or hubs without additional expensive wiring or equipment installation. Features • Conforms to IEEE 802.3, 802.3u, 802.3ab and 802.3x standards • Eight auto-negotiating 100/1000Base-T Ethernet ports on the GS-1008 Getting to Know the Dimension GS-1008/GS-1016 Gigabit Ethernet Switch Figure 1-1 GS-1008 Chapter 1 GS-1016 1008/GS-1016. -
Page 14: Package Contents
Rack mount kit Backbone Switch Network Application This section provides a sample of network topology in which the switch is used as a high-bandwidth backbone. The switch is an ideal upgrade for 100Mbps Ethernet networks. You can connect existing switches, hubs or computers with Gigabit 1000Base-T Ethernet adapters to the switch. -
Page 15: Figure 1-2 Backbone Switch Application
Dimension GS-1008/GS-1016 Gigabit Ethernet Switch Figure 1-2 Backbone Switch Application Getting to Know the... -
Page 17: Chapter 2 Hardware Description And Installation
Hardware Description and This section shows two switch installations, describes the switch hardware and The switch is suited to an office environment where it can be rack mounted on standard EIA racks or as a standalone. For proper ventilation, allow at least 4 inches (10 cm) of clearance at the front, 3.4 inches (8 cm) at the back of the... -
Page 18: Rack-Mounted Installation
Do not block the ventilation holes. Leave space between Rack-mounted Installation The switch can be mounted on an EIA standard size, 19-inch rack or in a wiring closet with other equipment. Follow the steps below to mount your switch on a standard EIA rack using the included rack-mounting kit. -
Page 19: Figure 2-2 Attaching Mounting Brackets And Screws
Figure 2-2 Attaching Mounting Brackets and Screws 2. After attaching both mounting brackets, position the switch in the rack by lining up the holes in the brackets with the appropriate holes on the rack. Secure the switch to the rack with the rack’s mounting screws. -
Page 20: Rear Panel
Connect one end of the supplied power cord to the power receptacle on the back of the switch and the other end to the 100-240V AC, 50-60Hz power source. For the GS- 1016, push the power switch to the ON position. -
Page 21: 100/1000Mbps Rj-45 Auto-Negotiating Ports
It allows data transfers of either 100 Mbps or 1000Mbps in either half-duplex or full- duplex mode depending on your Ethernet network. 2.4.2 Auto-sensing (Auto MDI/MDIX) Ports You can connect each RJ-45 auto-sensing port to a computer, hub or switch using either a straight-through or a crossover Ethernet cable. 2.4.3 Front Panel Connections You can use unshielded twisted pair (UTP) or shielded twisted-pair (STP) Ethernet cables for RJ-45 ports. -
Page 22: Front Panel Leds
2.4.4 Front Panel LEDs The LEDs give real-time status information. The following table provides LED descriptions. Figure 2-8 GS-1008 LEDs Figure 2-9 GS-1016 LEDs Hardware Description and Installation... -
Page 23: Table 2-2 Front Panel Led Descriptions
FDX/COL) Hardware Description and Installation Dimension GS-1008/GS-1016 Gigabit Ethernet Switch The switch is turned on and receiving power. The switch is off or not receiving power. A link to a 1000Mbps Ethernet device is up. The port is not connected to a 1000Mbps Ethernet device. -
Page 25: Chapter 3 Troubleshooting
100 - 240V AC, 50/60Hz power source. Make sure the power source is turned on and that the switch is receiving sufficient power. If these steps fail to correct the problem, contact your local distributor for assistance. -
Page 26: 100, 1000 Leds
Table 3-3 Troubleshooting 100, 1000 LEDs STEPS Check the connection between the switch and your Ethernet device(s). Verify that you are using the proper cable type and that its length does not exceed 100 meters. For more information on network cable types, see 2.4.3 Front Panel Connections. -
Page 27: Table 3-5 Troubleshooting Improper Network Cabling And Topology
A data path loop forms when there is more than one path or route path between two networked computers. This results in broadcast storms that will severely affect your network performance. Make sure there are no loops in your network topology. Troubleshooting Dimension GS-1008/GS-1016 Gigabit Ethernet Switch PROBLEMS AND CORRECTIVE ACTION... -
Page 29: Appendix A Product Specifications
Data Buffer Weight Product Specifications Dimension GS-1008/GS-1016 Gigabit Ethernet Switch Product Specifications This section provides the specifications of the switch. GENERAL IEEE802.3u 100Base-TX Fast Ethernet (twisted-pair copper) ANSI/IEEE802.3 Auto-negotiation IEEE802.3x Flow Control IEEE802.3ab 1000Base-T Gigabit Ethernet 1000BASE-T Ethernet ports (GS-1008: 8, GS-1016:16) - Page 30 Dimension GS-1008/GS-1016 Gigabit Ethernet Switch Dimensions Power Supply Power Consumption Operating Temperature Operational Humidity Safety Per Port (GS-1008: (4 LEDs) 100, 1000, LK/ACT (Link/Activity), FD (Full-duplex) Per Port (GS-1016: (3 LEDs) 1000, LNK/ACT (Link/Activity), FDX/COL (Full-duplex) Per Unit: Power 440(W) x 224(D) x 44(H) mm (19” in width rack mountable)
-
Page 31: Index
1000Base-T ...1-1, 1-2 802.3... 1-1 802.3ab... 1-1 802.3u... 1-1 802.3x... 1-1 About the Dimension GS-1008/GS-1016 Gigabit Ethernet Switch ... xii Auto MDI/MDIX ...1-2, 2-5 Auto-negotiating...1-1, 1-2 Auto-negotiation... 2-5 Auto-sensing ... 1-2 Cabling Length... 3-3 Campus Environment ... 1-1 CE ... iv Certification... - Page 32 Non-standard network cables...3-3 Package Contents...1-2 Plug-and-Play ...1-2 Power Connection...2-4 Power Receptacle ...2-4 Product Specifications General ... A Performance and Management ... A Physical Environment ... A Rack-mounted Installation...2-2 Rear Panel...2-4 Related Documentation ...xii Repair ...iii Return Material Authorization number...iii RJ-45 ports...2-5 Service ...iii Speed ...3-2 Store-and-Forward Switching...1-2...